Beam AB is supported by cable CD and a frictionless pin at H. The resulting reaction force acting on D due to the cable tension is D = 200i+140j lb , and the resulting reaction force acting on H due to the pin is H =-200i + 60j lb. Draw the shear and bending-moment diagrams for the beam AB. Use the sign convention for shear and bending moment that is given in the text. y 10 in. HO 8 in. 4 in. A E F G В 50 lb 100 lb 50 lb 10 in. +10 in.- 6 in. 6 in.

Beam AB is supported by cable CD and a frictionless pin at H. The resulting reaction force acting on D due to the cable tension is D = 200i+140j lb , and the resulting reaction force acting on H due to the pin is H =-200i + 60j lb. Draw the shear and bending-moment diagrams for the beam AB. Use the sign convention for shear and bending moment that is given in the text. y 10 in. HO 8 in. 4 in. A E F G В 50 lb 100 lb 50 lb 10 in. +10 in.- 6 in. 6 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.2 m, b = 4.4 m, c = 3 m, P = 16 kN, w = 34 kN/m, and Q = 26 kN. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally:(a) Determine V and M in the beam at a point located 0.65 m to the right of B.(b) Determine V and M in the beam at a point located 1.40 m to the left of C.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Draw the normal force (N), shear force (T) and bending moment (M) diagrams of the beam whose span and loading condition are given in the figure. L3(m)=1.5 L4(m)=2 P3(kN)=44 P4(kN)=82
The beam AB supports two concentrated loads P and Q. The normal stress due to bending on the bottom edge of the beam is +55 MPa at D and +37.5 MPa at F. (a) Draw the shear and bending-moment diagrams for the beam. (b) Determine the maximum normal stress due to bending that occurs in the beam.
determine the diagram of the shear forces and bending moments in the beam shown below. Data P = 20kN, M = 60kNm, q = 10kN / m, a = 5m, b = 2m, c = 3, alpha = 60.
Give the expression for the shear force, V = V(x), and the bending moment,M = M(x), as a function of the distance, x, measured from point A.Hint: Find the expressions of shear force and bending moment in each section:AB (0< x <4), BC (4 <x <7) and CD (7< x <10)
Construct the shear force and bending moment diagram with the help of free body diagrams (value of Y=7)
Draw the shear force diagram and bending moment diagram for the loaded cantilever beam as shown in figure. Mark all salient point in the diagram. Neglect the self-weight of the beam. Where P=3m, Q=2m, R=3m, S=3m, F1=20 N, F2=10N, U=15N/m. (i) The reaction at A (unit is in N) = ___________ (ii)Shear force at "A" (Unit is in N) =_______________ (iii)Shear force at "B" (Unit is in N) =_______________ (iv)Shear force at "C" (Unit is in N) =_______________ (v) Shear force at "D" (Unit is in N) =_______________ (vi) Shear force at "E" (Unit is in N) =_______________ (vii) Bending moment at "E" (unit is Nm) = __________ (viii) Bending moment at "D" (unit is Nm) = __________ (ix) Bending moment at "C" (unit is Nm) = __________ (x) Bending moment at "B" (unit is Nm) = __________ (xi) Bending moment at "A" (unit is Nm) = __________
The beam weight is 5kN considered as a distributed load over the beam length. Two bushwalkers with 850N weight each are standing together at one end of the beam/bridge. Determine the maximum shear force and bending moment in the simply supported beam shown below.
write the shear and moment equations and draw the shear and moment diagrams fig. P4.1 and fog.P4.2
Find the horizontal reaction and vertical reaction at A and also the vertical reaction at B. Determine the Internal forces at point C. Construct the shear and moment equations/functions at segment DE (1.5 < x < 3.0).Note point D is at 1.5m from A and point E is 3.0m from A.
For the beam and loading shown, write the equations for the internal shear force V and bending moment M as a function of x and then draw the shear and moment diagrams. Also, state the values of the internal shear force and bending moment at x = 1.4 m and x = 4.9 m. [Answer: At x = 1.4 m, V = 8.51 kN and M = -23.5 kN m and at x = 4.9 m, V = 2.93 kN and M = -2.77 kN m]
Determine the bending moment M in the beam at the point located 0.44 m to the right of point B. The ground reactions and shear-force diagram are shown.