briefly 1. Valve lag 2. intake lag

Q: name and explain the different control valve in steam generation

A:

Q: Which of the following methods are used to control the capacity of a centrifugal compressor? (Unit…

A: Centrifugal compressor is also known are also radial compressor. Main components are inlet…

Q: The wind speed beyond which the turbine should stop its operation is triggering speed cut-in speed…

A: Cut out speed, wind speed beyond cut out speed, the turbine should stops its operation. Every wind…

Q: Find the exhaust pressure for the compressor

A: Given     Intake Properties           Pressure, P1 = 12 psia           Temperature, T1 = 2oC Exhaust…

Q: Comment on the magnitude of this force and how it might need to considered in the mounting of the…

A: Given Data The initial temperature is:Ti=20°C The volume flow rate is:V˙=120litres/minute=120×10-3…

Q: Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says…

A: If carbon deposits form on the valves or valve seats, the valves will be unable to close properly.…

Q: What determines the cut off point in performance of wind turbine

A: Turbines cut in and cut off speeds are determined by the manufacturer to protect the turbine from…

Q: explain 2-stage reciprocating air compressor

A: An compressor is a device which will delivers the higher pressure with the help of some mechanical…

Q: Chaper 32 question 2 What can be used to check for leaks on the presure side of a turbocharger…

A: The leaks from the turbocharger of air can occur both on the vacuum side, one is air intake to the…

Q: tech a says that the float type carburetor is the least efficient design used on Briggs engines.…

A:

Q: Valves are favored because of their lower cost and lighter weight poppet plug ball Ο Ο Ο Ο butterfly…

A: Option (d) is correct : Butterfly

Q: Explain the main cause of abnormal combustion in the engines.

A: Possible causes  The heat value of the spark plugs too low. Mixture too lean, resulting in higher…

Q: In an IC engine the inlet valve diameter will be bigger than the outlet valve ? Select one: O True…

A:

Q: 2)which one of the following valve does not contain check valve inside? A)unloading valve…

A: A sequence valve could be a pressure valve outlined to open when its set weight is come to,…

Q: type of vane used in pump centrifugal? a. semi open straight b. semi open curved c. open type curved…

A: Option e is correct

Q: What device in the valve train changes rotary motion into reciprocating motion? a. Eccentric Cam…

A: Given Data⇒ Valve train Rotary motion Reciprocating motion

Q: Draw a schematic diagram of a supercharged engine and a turbocharged engine layout:

A: Given:- Supercharged turbocharged engine brief introduction To find:- Schematic of Supercharged…

Q: what is clearance volume in engine?

A: Clearance volume is defined with a schematic diagram

Q: Which of the following is true of variable intake manifolds? a)they are designed to reduce intake…

A: Solution:

Q: me in and com mps and valve w and return

A: In central heating system two types of pipes are used,

Q: ". Compressor blades are twisted from root to tip:

A: Compressor blades are twisted from root to tip

Q: Define valve margin

A:

Q: Explain basic concept of turbocharger or supercharger.

A: "Supercharger" is the generic term for an air compressor used to increase the pressure or…

Q: Which one of the following is a component of a centrifugal compressor? a. Suction valve b. Nozzle…

A: Although the centrifugal compressor is unlikely to be used in gas turbine plants where specific fuel…

Q: 6. Vanes have a negative impact on the pressure drop inside duct elbows. 7. High degree of superheat…

A: given:

Q: Number of times the intake valve opens in a single-cylinder four-stroke cycle after completing 200…

A: Given:- Single Cylinder  Four stroke cycle Number of revolution = 200  To Find:- Number of times the…

Q: es are favored because of their lower cost and lighter weight Correct answer plug ball poppet…

A: To select the correct options.

Q: Briefly explain the difference between a gasoline-powered and diesel powered-engine.

A: Gasoline power engine works on Otto cycle that is in gasoline engine constant volume heat addition…

Q: Describe and draw how the 2 strokes diesel engine works.

A:

Q: How does a servo valve work?

A: Servo Valve :  A servo valve is also considered as directional control valve and They are capable to…

Q: A- Briefly compare between actual and theoretical valves timing with drawing.

A: Theoretical valve timing diagram:  In theoretical valve timing diagram suction and exhaust valve…

Q: Relative Centrifugal Force (RCF) RCF = 1.119 x 10-$ x (rpm)² x

A: Relative Centrifugal Force (RCF) is the sum of acceleration to be applied to the test. It depends…

Q: umerate the advantages and disadvantages of the following types of engine: a.) Rotary or Wankle…

A: C) Rotary Engine Advantages 1.it has higher power to weight ratio. 2. it has no reciprocating…

Q: What provisions are usually included on tractor engines to aid in the correct timing of the…

A: A cambelt, timing chain, or timing belt is a component of the internal combustion engine of the…

Q: Compare rotameter and valve tray - where is their similarity? Use sketches it required.

A: Rotameter:  Rotameter is used for the measurement of the volume flow rate by the use of floating…

Q: INTRODUCTION ABOUT VALVE SYSTEM IN INTERNAL COMBUSTION ENGINE

A: In this solution we will only discuss about the brief introduction about the valve mechanism in the…

Q: 10. List some valves used in industries and their functions.

A:

Q: coefficient of obstruction due to gate valve (only table please)

A: coefficient of obstruction (k) is used to measure the head loss due to valves and other fitting. It…

Q: conclusion about learning the valve system of Internal Combustion Engine (ICE) and explain how it…

A:

Q: Describe and draw how the 4 strokes diesel engine works

A: The four-stroke engine is one of the most prevalent types of internal combustion engines, and…

Q: What part is often changed with a water pump? Select one: a. A crankshaft pulley b. A timing belt

A: Generally, the idler pulleys, tensioner and water pump ought to continuously be replaced when the…

Q: is it true that an l head engine has the intake and exhaust valves mounted in the cylinder head

A: Solution:

Q: List out the design requirements of diesel engine combustion chamber

A: Diesel engines work on the diesel cycle. In diesel engines, the air is compressed alone and at the…

Q: Draw in askerch an impelMer of turbomachine explain its Parts aned the velocity triengle at one…

A:

Q: Discuss the main functions of the lubricating system of an engine

A: Solution:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.