2- Consider a liquid level system as shown in the following figure, design a suitable feedback system elements to control output (h). use a suitable feedback system elements to control output head (h) according to require temperture (Ta = 300°). Attempt with the following: %3D h = 8m A = 600m? a- Choose a suitable level sensor. b- Use a suitable mechanical amplifier. c- Draw a sckematic diagram to discribe the complete feedback system, then draw a complete block diagram.

2- Consider a liquid level system as shown in the following figure, design a suitable feedback system elements to control output (h). use a suitable feedback system elements to control output head (h) according to require temperture (Ta = 300°). Attempt with the following: %3D h = 8m A = 600m? a- Choose a suitable level sensor. b- Use a suitable mechanical amplifier. c- Draw a sckematic diagram to discribe the complete feedback system, then draw a complete block diagram.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.3P

See similar textbooks

Similar questions

For the open-loop system G(s) = 3/s^2 + 2s - 3 assume there is a feedback with a proportional gain, K. And sketch a locus of closed-loop rootsverse K. What is the minimum value of K to achievea stable system?
Topic: Feedback and Control System Block Diagram Algebra and Transfer Functions of SystemWill leave a like if the answer is correct, please check the instructions carefully, thanks!
3- Consider the unity feedback system shown below. a)Find the range of k for which the closed-loop system is table. b)What is the steady-state error for unit ramp and step inputs.
Consider a unity negative feedback system with loop transfer function shown in Figure where L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1)L(s)=GcG(s)=K(s2+6s+1)(s2+5s+1) Determine the value of K for which the closed-loop system is stable.
For the unity feedback system given below, the damping ratio of the closed looppoles is given by a) 1.5 b) 1 c) 0.5 d) 0.25
The block diagram below shows a feedback controller for a skyscraper elevator’s vertical position. (a) Determine the closed-loop transfer function of the system, HCL(s) = Y(s)/R(s).(b) Assume that all initial conditions are zero. From HCL(s) in part (a), derive the equation of motion of the system.(c) Define the state variables of the system as phase variables and substitute them into the equation of motion in part (b).(d) Define the control input vector as u(t) = r(t). Rewrite the equation of motion in part (b) instate-space form, xdot = Ax+Bu.(e) Define 2 outputs: the elevator position and the elevator velocity. Write the output equation in state-space form, y = Cx + Du.
Feedback Control 2. Consider the unit-step response of unity-feedback control system whose open-loop transfer function is ?
For the system shown in Figure 3, first find the values of K1 and K2 to obtain a peak time of 1 second, and a settling time of 2 seconds, for the closed-loop step response of the system. Then find the poles of the closed-loop transfer function, T(s) = C(s)/R(s). Construct the corresponding graph of poles and zeros
In the unity feedback system, what is the system type and find the appropriate steady-state error and error constant associated with system type for step, ramp, and parabolic inputs
Is this system internally stable? Now, consider the following feedback diagram: where ? denotes the system above. Is this new overall system internally stable? Comment on the result.
Consider the unity feedback control system in Figure where L(s)=Gc(s)G(s)=K(s)(s+4) For an underdamped response, the design specifications for a reference unit step inputs are: i. Peak time Tp=1.0 ii. Percent overshoot P.O.≤%10 Calculate the value ofKfor each design specification separately. Do not forget to make comments about the design parameters
An open-loop system is described by the differential equation (see picture). A) Is this system stable. Why? This system is now connected with unity feedback. B) Write the loop transfer function, G(s)H(s); C) Determine the gain and phase margins of the closed loop system and comment on stability.