(c) Propose a machining operation for a raw material as shown in Figure 3(a) and explain every step involved to produce an end product as shown in Figure 3(b) as well as input parameters that you control during the operation. State all measurement tools used and safety precautions taken. 125 Ø32 (a) 100 20 95 45 Ø20 Ø10 Ø20 Ø30 (b) Figure 3 [Gambarajah 3]

(c) Propose a machining operation for a raw material as shown in Figure 3(a) and explain every step involved to produce an end product as shown in Figure 3(b) as well as input parameters that you control during the operation. State all measurement tools used and safety precautions taken. 125 Ø32 (a) 100 20 95 45 Ø20 Ø10 Ø20 Ø30 (b) Figure 3 [Gambarajah 3]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a matrix of 0.1 mm (0.004 in) diameter holes in a plate of 3.2 mm (0.125 in) thick hardened tool steel. The matrix is rectangular, 75 by 125 mm (3.0 by 5.0 in) with the separation between holes in each direction = 1.6 mm ( 0.0625 in).
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
Q#4: Explain the function(s) of electrolyte in Electro-chemical Machining process.
During a certain machining experiment at the UCSI workshop, it is observedthat temperature at the tool workpiece interface is 1200 oC at a cutting speed of300 mm/min with a feed rate of 0.002 mm/rev. (i) Analyse how the temperature will be affected if the cutting speed isincreased by 100 %.(ii) Determine the cutting speed necessary to achieve a maximum cuttingtemperature of 900 oC
In an orthogonal cutting test with a bar of 75 mm diameter is reduced to 73 mm by using a HSS tool with arake angle  = 10o, following observations were made: length of the chip, lc = 69.44 mm, cutting ratio r =0.3, the horizontal component of the cutting force, FH = 1450 N, and the vertical component of the cuttingforce, FV = 850 N. The various parameters recorded in this cutting operation are: depth of cut, d = 2 mm;feed rate, f = 0.3 mm/rev, cutting speed, V = 60 m/min. Using Merchant’s theory calculate the following:1) Friction force along rake face2) Normal force acting on rake face3) Shear force along the shear plane4) Normal force acting on shear plane5) The percentage error in shear angle predicted by Merchant’s theory6) Shear velocity7) Chip velocity8) Total work done9) The shear work proportion out of the total work done10) The friction work proportion out of the total work done
A shaft of 0.5 m in length and 100cm in diameter is to be machined. What operation will you utilize on lathe to bring the specimen of size 50 cm diameter and 0.25 m length?
2 1.42 The tool-life curve for ceramic tools in Fig. 21.17 is to the right of those for other tool materials. Why?
The average number of articles produced by two machines per day are 200 and 250 with S.D 20 and 25 respectively on the basis of records of 25 days production.Can you regard both the machines equally efficient at 1% level of significant?
A high-speed steel tool is used to turn a steel workpart that is 295 mm long and 75 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 80 (m/min) for a feed of 0.5 mm/rev. The operator and machine tool rate = $29.00/hr, and the tooling cost per cutting edge = $3.90. It takes 2.1 min to load and unload the workpart and 3.40 min to change tools. Determine (a) cutting speed for maximum production rate, (b) tool life in min of cutting, and (c) cycle time and cost per unit of product (d) cutting speed for minimum cost and tool life in min of cutting
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
22.24 What precautions would you take in machining with brittle tool materials, especially ceramics? Explain.
For the following application, identify one or more nontraditional machining processes that might be used, and present arguments to support your selection. Assume that either the part geometry or the work material (or both) preclude the use of conventional machining. The application is a through-hole in the shape of the letter L in a 12.5 mm (0.5 in) thick plate of glass. The size of the "L" is 25 by 15 mm (1.0 by 0.6 in) and the width of the hole is 3 mm (1/8 in).