Calculate the magnitude of the force supported by the point at A under the action of the 1.9-kN load applied to the bracket. Neglect friction in the slot. - 130 mm 110 mm 1.9 kN 37°

Q: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,…

A: Option (b): Tmax = 300 kN , S = 75 m

Q: 400 kN 800 kN 6 m D 3 m A 3 m 6 m E 6 m 200 kN 200 kN B.

A:

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Find the angle of tilt 6 with the horizontal so that the contact force at B will be one-half that at…

A: Given:

Q: Find the distance x (measured along AB) at which a horizontal force of 60 lb should be applied to…

A:

Q: The portable floor crane in the automotive shop is lifting a 530-lb engine. For the position shown…

A: Find force at support C and pressure in piston Load =530 lb

Q: The machine part of negligible weight is supported by a pin at A and a roller at C. Determine the…

A: Given data as per the question Force applied at point B =3 KN considering the given structure and…

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A:

Q: Determine the force in member BC in kN.

A: Need to determine the force in member BC

Q: 4/1 Determine the force in each member of the loaded truss. -12 m- 5 m 100 kg

A:

Q: Calculate the magnitude of the force supported by the pin at A under the action of the 1.5-kN load…

A: Given data :  Load = 1.5KN = 1.5 x 103N Q = 30 Find :  Force at A = ?

Q: Two members, each consisting of straight and 168-mm radius quarter-circle, are connected as shown…

A:

Q: Determine the magnitude of force P (in Ib). *

A:

Q: The signboard truss is designed to support a horizontal wind load of 950 lb. If the resultant of…

A:

Q: PROBLEM 3.Rod XY and smooth surface O hold the 1600-N cylinder in equilibrium as shown. Find the…

A: Given data: Weight of the cylinder, w = 1600 N. Draw the free-body diagram of the cylinder as…

Q: Find the angle of tilt θ with the horizontal so that the contact force at B will be equal to 0.26…

A: NB=.26NA angle of tilt θ FBD of smooth cylinder

Q: Determine the force magnitude P required to lift one end of the 250-kg crate with the lever dolly as…

A:

Q: In a hydraulic press, the small cylinder has a diamter of 1 in, while the large piston has a…

A: To Find : The force on the large piston. Given :  The diameter of larger piston is d=8 in. The…

Q: Determine the force in each member of the Gambrel roof truss shown. State whether each member is in…

A: Total load= (300 lb+600 lb+ 600 lb+ 600 lb+ 300 lb)                  =2400 lb   Due to the symmetry…

Q: A force of 20 lb is required to pull the stopper DE Determine all forces acting on member BCD. in…

A: Given, P=20 lb  Now free body diagram of the given structure,  From the equilibrium sum of…

Q: The boom shown has a negligible weight and supports the 1000 N load. A B 60° 1000 N Determine the…

A: given data weight of the block = 1000 N to determined- compressive force in the boom BC

Q: Find the angle of tilt with the horizontal so that| the contact force at B will be one-half that at…

A: Dear student as you have posted multiple Question as per the policy i can solve only one question so…

Q: Q3) A lug wrench is used to tighten a square-head bolt. If 50-lb forces are applied to the wrench as…

A: Q3. Draw front view of wrench

Q: Calculate the reaction force at support B Calculate the reaction force at support B when the support…

A: Given: A propped cantilever beam as shown in Fig w= 7kN/m P= 14kN flexural rigidity (EI)= 4 MN.m2…

Q: Determine the force P required to maintain the M-kg engine in the position shown in the figure . The…

A:

Q: mop.onilsHTAM 3 m 4 m |3 m MATHalino.com 600 3 m 3 m 3 m 3 m 30 kN 30 kN 90 kN

A: Given:-  Truss  To Determine :- The magnitude of the force members of the truss Solution:-  Firstly…

Q: The indicated location of the center of gravity of the ( 16 kN ) pickup truck is for the unloaded…

A: Given, Weight of the car = W = 16 kN Distance x = 40 cm   Consider below FBD for the given…

Q: The dump truck consists of a chassis and a tray, with centers of gravity at G1 and G2, respectively.…

A:

Q: Determine the value of force P (in N).

A: To determine the value of Force

Q: A heavy spool rests on the ground at point A and against the wall at point B. Find force F required…

A: Given that, Mass of the spool, m=100 kg,Radius of spool, ri=200 mm, and ro=460 mm,Coefficient of…

Q: Use the method of members to determine the true magnitude and direction of the forces in each of the…

A: Given:- AB=1' BC=1' CD=2' Load at B=100lb Angle θ=30° To find:- Forces in members 1 and 2

Q: Find the forces in member FD and member FE.

A:

Q: Determine the magnitude P of the vertical force required to lift the wheelbarrow free of the ground…

A:

Q: 2. The L-shaped bracket is bolted securely to the shaft at O, so that the bracket cannot move in any…

A: The x-component of reaction at O is, Fx=F2cos50°Fx=0.643F2 The y-component of reaction at O is,…

Q: 1. The telephone pole AB weighing 3730 N is resting in a hole that is 2 m deep. If the contact force…

A:

Q: 60 mm, 60 mm A R=75 mm 105 mm 100 N

A:

Q: The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown…

A: Given Data The angle of the crane is: θ=32° The distance a is:a=7 in The distance b is: b=34 in The…

Q: A block with a mass of 150-kg is supported by a cable which passes over a 150-mm diameter pulley…

A: Given The mass of the block = 150 Kg The tension in the string W = 150*10 = 1500 N The diameter of…

Q: Calculate the magnitude of the tension T and the angle O for which the eye bolt will be under a…

A:

Q: dAB F1 = 20 kN, F2 = 30 kN B At a) Calculate the force P that will keep the system F2 kN in balance.…

A:

Q: As per the crane shown in the Figure. Determine the force member at CE.

A:

Q: Q2/Calculate the magnitude of the tension T and the angle 0 for which the eye bolt will be under a…

A:

Q: Determine the force in member CE of the truss. (Note that "kips" is used for kilo-pounds, or 1000…

A: GIVEN DATA A PLANE TRUSS GIVEN WE HAVE TO FIND FORCE IN MEMBER CE OF THE TRUSS METHOD USED - METHOD…

Q: Determine the axial force in members of the truss system below a. Axial force on member marked with…

A:

Q: Calculate the forces, in Newtons, for the following: (d) member FG (e) pin H (f) hydraulic cylinder…

A: Given: The load, P = 724 N The angle, θ = 34.5°