Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m³, the volumetric oil flowrate is 720 L/min, and the dynamic viscosity of water is 1.2 centipoise

Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m³, the volumetric oil flowrate is 720 L/min, and the dynamic viscosity of water is 1.2 centipoise

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.1P: Evaluate the Reynolds number for flow over a tube from the following data: D=6cm,U=1.0m/s,...

See similar textbooks

Related questions

Q: A simplified heat utilization system of a Geothermal Power Plant provides the following data: Mass…

A: Option ( B) is correct W= 2160 KJ

Q: The simply supported beam consists of a W14 × 34 structural steel wide-flange shape [E = 29,000 ksi;…

Q: 2. When a 7.5 KN force is hung at the end of these 3 springs which are equidistant to each other and…

Q: A Kaplan turbine has a runner diameter of 4 m and a hub diameter of 1.2 m. The discharge through the…

A: The runner diameter is 4 meter and the hub diameter is 1.2 m. The discharge of the fluid through…

Q: Quiz 2 Find me components of F = 200N Shown in fig with respect to X-axis & y=axis

Q: (VA)2 ()1 = 0.5 fus 45° 30° 30 B "g) = 0.8 fu/s (VR)2 The following impact is observed to occur…

Q: (Industrial safety) What is the concept of ALARP? Give an example of a situation where the ALARP…

A: Danger must be weighed against the trouble, effort, and money it will take to mitigate it. As a…

Q: 1.) An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594…

Q: Calculate the bending moment at point B and upload your file in the next question where you draw the…

Q: Q2: The pendulum consists of a 15 kg sphere and a thin bar of 5 kg. Calculate the reaction on pin O…

Q: Fossil fuel power plant generates power to 5 residential household community with the following…

Q: What is the maximum speed that the one-ton vehicle can travel over the hill and not lose contact…

Q: Question 3 As a means of measuring the viscosity, a liquid is forced to flow through two very large…

A: Given: To explain:

Q: WORK ENERGY AND POWER COMPLETE SOLUTION A 2kg block hits the spring with a speed of 4 m/s. Determine…

Q: What is the chain rule for angular velocity? If we know the angular velocity of the Orbital CCS…

Q: What is the significance of the Determination of the coefficient of discharge of a 90-degree…

Q: Mathematical expressions of power output ration with power input? A Energy Efficiency (B) Capacity…

A: Mathematical expression of power output ratio with power input is called energy efficiency.

Q: What are the advantages of forging process?

A: Advantages of forging 1. Parts manufactured are stronger. 2. Forging offers high ductility. 3.…

Q: Given four series springs in a viscous damped system with a stiffness of 600 N/m, critical damping…

Q: A 400-mm-long rod with a diameter of 4.5 mm is loaded with a 5000-N weight. If the diameter…

Q: A power plant operating on a Rankine cycle has steam entering the turbine at 500 °C and 2 MPa. The…

A: Given data Conditions of steam entering the turbine = 500° C and 2 MPaTurbine efficiency = 85%Pump…

Q: How much more time(minutes) needs to pass to reach 47°C.

Q: A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The pipe then breaks…

Q: Calculate the velocity v of the 50-lb cylinder after the 20-lb cylinder has dropped 6 ft. 41 lb 50…

A: m1= 50 lbm2= 41 lbm3= 20 lb20 lb cylinder has dropped 2 ft.Hence, y1= -6 ft, y2= 6 ft, y3= 6 ft To…

Q: The left field wall at a baseball park is 320 feet down the third base line from home plate; the…

Q: A sprinkler system pumps water through a large pipe inlet with a diameter (d). The pipe then breaks…

Q: Q5: The 15 kg cylinder rotates with an angular velocity of 40 rad/s. If a force F = 6 N is applied…

Q: Can someone help me fill out this worksheet please?

A: Given Cross-section diagram To find Fill in the blanks

Q: A shaft is loaded in bending and torsion such that Ma= 70 N m, Ta= 45 N. m, Mm = 55 N m, and Tm= 35…

Q: y wo wo A 0.67 L 0.33 L-

Q: A geothermal power plant was installed at the rear side cliff of Mayon Terrain that generates…

Q: What water level H must be maintained in the tank as shown in Fig. P. 3.5.20 to deliver a flow rate…

A: Flow rate, Q= 5×10-4 m3/sec Friction factor, f= 0.0295 D= 25 mm= 0.025 m L= 25 m To find: Water…

Q: What water level H must be maintained in the tank as shown in Fig. P. 3.5.20 to deliver a flow rate…

Q: Compute the Total work of a plant if the the combined cycle overall efficiency is the average value…

A: Combined cycle overall efficiency is the average value Heat input= 192 kJoules= 192000 Joules To…

Q: A system of computer aided tools used by operator in electric utility grid to? A plan B optimize C)…

A: Option (B) is correct

Q: SA2) A 50-N force is used to push a 0.65 kg metal ball from rest. If the force is applied on the…

A: Given Force, F = 50 N Mass, m = 0.65 kg Time taken, t = 0.25 sec Find Final…

Q: Q' is the flow rate per unit width (i.e. has units of m2/s). Express Q' in terms of T When the flow…

Q: Q5: Determine the horizontal and vertical components of reaction at the pin A and the reaction of…

A: Let horizontal component of reaction at pin A is represented as AX. Let vertical component of…

Q: 4. The box beam is made of an elastic-perfectly plastic material for which the yield stress oy = 250…

A: Given Data : σy=250 mpaMep=548.6KNmflanges=260mm×30mmIx=247.8×106mm4Zx=2394000mm3

Q: Two vats are connected by a submerged pipe with a square cross-section, as shown in the image…

Q: Most modern electrical heating and cooling devices are provided with thermostat. What is the purpose…

A: given; Most modern electrical heating and cooling devices are provided with thermostat. What is the…

Q: 1.A uniform bar AB weighing 5OOKN, is fastened bya frictionless pin to a block weighing 100KN as…

A: Given DataWA=100kNWbar=500kNμkwall=0.268μkblock=0.2θ=45°To findP=? Free Body Diagram ***As per our…

Q: A simple solar water heater is shown in the image. Which tubing would give the hottest water from…

Q: engineer working in a car company, you are assigned to evaluate two new car models, the Car A and…

A: Hjaja

Q: 1.) An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594…

Q: about 1. Find the moment of the force (200N) point o.

Q: An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594 °C.…

Q: The apples fall from the hand of a person in an elevator that moves down quickly, 3 m/s. What is the…

A: Given , Initial velocity ,u= 3 m/sec Final velocity , v= 0 height, h= 2m

Q: What will be the velocity of the follower at 90° using the following equation with segment angle…

A: Find the velocity of follower at 90 °.

Q: Boom OAB is supported by a ball and socket at point O and two cables AC and AD. Determine the forces…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given Data

VIEW

Step 2 Calculation

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the volumetric flow rate (in li/hr) of a fluid flowing inside a pipe at a rate of 200lbm/hr. SG=2.56
The average velocity of water flow in a pipe with diameter 4 cm is 4 m/s. Calculate the amount of fluid flowing per second (Q).
.A venturi meter is used to measure liquid flow rate of 7500 litres per minute. The difference in pressure across the venturi meter is equivalent to 8 m of the flowing liquid. The pipe diameter is 19 cm. Calculate the throat diameter of the venturi meter. Assume the coefficient of discharge for the venturi meter as 0.96
A crude oil of specific gravity 0.9 is flowing through a pipe of diameter 200 mm and the frictional head loss of 4.5 m of crude oil between the two ends of a pipe which are 825 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.007 and kinematic viscosity as 12 stokes. The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Water, with a density of 1000 kg/m3 and a dynamic viscosity of 0.0013 kg/ms, is flowing through a pipe of radius 28 mm. Calculate the critical velocity?
What is the minimum pipe diameter in cm that can be recommended if the flow is 5 m^3/s and the design velocity if the system is 3 m/s?
A plugged dishwasher sink with the dimensions of 15 in. ✕ 19 in. ✕ 9 in. is being filled with water from a faucet with an inner diameter of 1 in. It takes 210 seconds to fill the sink to its rim. Imagine the plug of the sink leaks. If it now takes 230 seconds to fill the sink to its rim, estimate the mass-flow rate of the leak (in lbm/s). lbm/s
An orifice meter with a 5 cm diameter is used to measure the flow rate of liquid. Under a head of 4 m, the velocity of the liquid at vena contracta is 7.5 m/s. If the actual discharge through the pipe is 8 l/s, calculate the coefficients of velocity, discharge, and contraction. Include Free body Diagram
The volume flow rate of water is 662,73 liters/min. Calculate the maximum length of the pipe [m], which can be used without cavitation? (NOTE: Take water temperature as 10 °C)
Water flows at a rate of 0.185 m3/s through a 150 m long galvanized steel pipe of diameter 200 mm. Given that the kinematic viscosity of water, ν = 1.14 ×10–5 m2/s, and the average surface roughness for galvanized steel = 0.15 mm… Calculate: a) Loss of head due to friction. b) Pumping power required to maintain the above flow.
Oil of specific gravity 0.8 flows through a pipe of 0.25 m diameter. An orifice of 0.1m diameter is fitted to the pipe to measure the flow rate. A mercury manometer fitted across the orifice records a reading of 0.8 m. Calculate the coefficient of discharge of the orifice meter if the flow rate measured by it is 0.082 m3/s.
Calculate the Reynolds Number for a fluid with a dynamic viscosity of 0.38 N-s/m^2 and a density of 910 kg/m^3 which flows through a D=26.04 mm diameter pipe with a velocity of v = 8 m/s. Write answer in 2 decimals.