Calculate the yield of tert- butyl chloride if we take 7ml of tert- butanol and the actual mass of tert-butyl chloride was 5.7 gram (density of tert- butane=0.775g/cm3 ,Mwt of tert-butyle chloride =92.57g/mol , Mwt tert-butanol = 74.12g/mol) ,your calculation must consider the ratio between number of tert-butanol moles : tert- butyle chloride moles is 1: 1

Calculate the yield of tert- butyl chloride if we take 7ml of tert- butanol and the actual mass of tert-butyl chloride was 5.7 gram (density of tert- butane=0.775g/cm3 ,Mwt of tert-butyle chloride =92.57g/mol , Mwt tert-butanol = 74.12g/mol) ,your calculation must consider the ratio between number of tert-butanol moles : tert- butyle chloride moles is 1: 1

Pushing Electrons

4th Edition

ISBN:9781133951889

Author:Weeks, Daniel P.

Publisher:Weeks, Daniel P.

Chapter3: Mechanisms

Section: Chapter Questions

Problem 4EQ

See similar textbooks

Similar questions

If 0.70 g of FeCl3 is used to iodinate 8.42 g of benzene with sufficient ICl, what is the average number of reactions that each FeCl3 molecule must catalyze?
What is the simplest CGS unit for "poise"?
Isopentyl alcohol reacts with pure acetic acid to form isopentyl acetate, the essence of banana oil:C₅H₁₁OH+CH₃COOH⇌CH₃COOC₅H₁₁+H₂O A student adds a drying agent to remove H₂O and thus increase the yield of banana oil. Is this approach reasonable? Explain
one or more answers Which of the following will result in an increase in the calculated Ksp of Ca(OH)2? Receiving flask used during filtration was contaminated with HCl The Na2CO3 primary standard solution was overtitrated The saturated Ca(OH)2 solution was overtitrated Some Ca(OH)2 solid passed through the filter paper during filtration The water used to dissolve Ca(OH)2 solid was greater than the required amount
1) Commercial fuming Sulphuric acid (Oleum-H2S2O6) is 99.9% solution. Please convert it into molarity.2) Find out the Volume (dm3) of product (gas) at RTP when 0.58 M, 150 mL NaOH (aq.) reacts with 350 mL, 0.25 NH4Cl.
1. Calculate the percent by volume of acetic acid by fermentation. Assumptions: No volume changed during fermentation and conversion efficiency is 85%. Overall chemical reaction facilitated by Acetobacter aceti:C2H5OH + O2 = CH3COOH + H2OGiven: Volume of 6% C2H5OH = 3 LMolar mass of C2H5OH = 46.07 g/molMolar mass of CH3COOH = 60.06 g/molDensity of C2H5OH = 0.789 g/mLDensity of CH3COOH = 1.05 g/mL
When an organic reaction is undergoing reflux, what are some potential errors (not human or instrumental) that would cause the reflux to be incomplete?
#1. Part A. in a drug discovery program, a hit compound________. A. Shows activity in an animal model of disease B. Is active in target/ whole-cell assays in vitro C. Is purchased from a commercial vendor D. Is derived from screening natural product libraries Part B. When using TLC to monitor an organic chemistry reaction, which could be an indication that your desired reaction has gone to completion? A. the stationary phase changes colors B.the mobile phase runs to the top of the tlc plate C.the starting material spot disappears and a new spot appears D,the starting material spot remains on the tlc plate
Can you calculate the limiting reagent, theoretical yield and% Reaction Yield shown using reaction stoichiometry? The calculations given in the benzalacetone synthesis experiment were the volume of 3mL of benzaldehyde, 1mL of acetone and the mass of dibenzalacetone 2.69g. With this data I calculated the other data shown in the table. Thank you! Psd.Where it says " Que deseas hacer?" in the photo that is the Benzaldehyde data.
Preparation of 0.25N NaOH Objective: Apparatus and Materials: Procedure : Calculate the exact mass of NaOH needed to prepare 1.0L of 0.25N NaOH for standardization. Show your computations. Using the triple beam balance, weigh the desired amount of NaOH. Place the weighed amount of NaOH into the 500 mL volumetric flask and add distilled water until it reaches the mark. Agitate and transfer the solution into the reagent bottle. Add again distilled water to the same volumetric flask until it reaches the mark and pour it to the same reagent bottle, thus having a total volume of 1.0 L. Label the reagent bottle, 0.25N NaOH. Data and Computations: Conclusion:
Acetaminophen or paracetamol, the active ingredient in many pain killers absorbs in the UV range with a λmax at 250 nm in neutral solutions (methanol usually). Its extinction coefficient is 14 mM-1cm-1. Each commercially available tablet (Tylenol, Panadol or Herron) contains 500 mg paracetamol. Its molecular weight is 151.1. Using this information, calculate the dilution required to analyse the concentration of paracetamol in a commercially available paracetamol tablet. Start by dissolving the tablet in 100 mL methanol. Show working out.
Distinguish between mixed-acid fermentation and butanediol fermentation and describe the test(s) that can be used to detect each. Briefly describe the reactions and changes that take place during the decarboxylation of amino acids in the decarboxylase medium. Explain the experiment that you would perform in order to determine whether the organism that you were instructed instructed to identify is positive or negative for gelatin hydrolysis. How do microorganisms such as bacteria eliminate harmful reactive oxygen species? Nitrate reduction to nitrite is indicated by the formation of a pink to red color after addition of nitrate test reagent. However, if a culture does not produce a colour change several possibilities exist. Explain.