calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd.

calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd.

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter8: Stresses In A Soil Mass

Section: Chapter Questions

Problem 8.14P

See similar textbooks

Similar questions

A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Include FBD. a. 0.629 b. 0.989 c. 0.98 d. 0.636
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. Show fbd and solution a. 0.636 b. 0.629 c. 0.989 d. 0.98
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd, Cc, and Cv, Show a Diagram
A calibration test of a 2.5cm circular sharp edged orifice in the vertical side of the large tank showed a discahrge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measuremnt of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cc.CHOICES a.0.629 b.0.989 c.0.98 d.0.636
A calibration test of a 2.5cm circular sharp-edged orifice in the vertical side of the large tank showed a discharge of 590 N of water collected in 81 seconds, when under a constant head of 4.70 m. In addition, measurement of the trajectory of the jet gave the following data: A point on the jet has the coordinates in cm (235, -30), with the orifice located at the origin of the rectangular coordinate system. Find the value of Cd. answers: a.0.989 b.0.636 c.0.629 d.0.98
A calibration test of a 12.7mm circular sharp edge orifice in the vertical side of a large tank showed a discharge of 589N of water in 81 sec. at a head of 4.73. Measurement of the jet showed that it traveled 2.35m horizontally while dropping 0.0305m. Compute the three orifice coefficients.
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7.89cm radius?
A course sand sample is placed in the constant permeameter test. Water passes through the sample water with a constant head of 40cm and after 0.00167hr, 40grams of water have been collected. What is the coefficient of permeability of the sand in cm/sec if the sample is placed inside a 166cm container with a 7cm by 5cm dimension.
HYDROSTATIC FORCE ON PLANE SURFACE can someone help me analyze this experiment? For fully submerged: - compare the results of W x r with the calculated values of F x (Xcp + hs). - give reasons for discrepancies. - what can you obtain from the relationship of the graph? Does the experiment confirm the results of computed values of the magnitude and location of the total hydrostatic force?
for a sample of water ec reading was called 178 X 10^-3 siemens per centimeter calculate the value of tds in ppt
A permeability test was carried out from a well that sunk through a surfacelayer of loose sand. Figure below shows the arrangement of pumping wells, togetherwith relevant dimensions. Initially, the piezometric surface (ground water table) waslocated at a depth of 2.5m. When steady state was achieved at a pumping rate 38.5 m^3/hr, the following drawdowns were observed. Pumping well, d0 = 3.64mObservation well, d1=0.96mObservation well, d2 = 0.48m Calculate the coefficient of permeability of the sand in m/hr
24/27/30 After conducting a fall cone test, the regression equations obtained from the 80g and 240g cones were w=38.2log(d)+13.1 and w=38.2log(d)+2.3, respectively. Determine the liquid limit and plastic limit.Determine Δw. Note: w (%) is the moisture content and d (mm) is the depth of penetration.