Choose one of the solutes. Add more solute until you have 1L. Shake in as much solute as you have to in order to achieve saturation. Now, begin evaporation, paying attention to the bottom of the chamber. What do you observe? Why? What if we were able to change the temperature of the solvent? How would that affect saturation? Make sure to include at least two possibilities (i.e. if heat were added...or if heat were taken away/cooled...)

Choose one of the solutes. Add more solute until you have 1L. Shake in as much solute as you have to in order to achieve saturation. Now, begin evaporation, paying attention to the bottom of the chamber. What do you observe? Why? What if we were able to change the temperature of the solvent? How would that affect saturation? Make sure to include at least two possibilities (i.e. if heat were added...or if heat were taken away/cooled...)

Organic Chemistry: A Guided Inquiry

2nd Edition

ISBN:9780618974122

Author:Andrei Straumanis

Publisher:Andrei Straumanis

Chapter4: Polar Bonds, Polar Reactions

Section: Chapter Questions

Problem 7E

See similar textbooks

Similar questions

The process of Distillation is able to concentrate ethanol because: a. the boiling point of ethanol (78oC) is lower than the boiling point of water (100oC) b. CO2 is a gas that occupies ~22 liters per mole whereas ethanol is a liquid dissolved in water c. adding egg white traps CO2 bubbles which allows them to be separated from alcohol d. Sodium Aluminum Phosphate binds ethanol and concentrates it e. distillation removes the reducing equivalents “H2” from ethanol and lowers the calorie content making “light” calorie beverages
what is the freezing method on separating alcohol to the mixture and its step by step process
Which of the following is/are TRUE about simple distillation technique? a. It is used to separate thermally labile components of a liquid mixture. b. It is used to separate components of a liquid mixture with high differences in boiling points. c. It is used to separate components of a liquid mixture wherein the mixture boils at a temperature lower than the boiling points of the components. d. All of the above.
What are you looking for specifically when doing the microscale boiling point? Whatcauses the bubbling initially? What causes the final rapid bubbling?
Benzillic Acid Lab Q3. Cold water and ethanol was used to wash/rinse the collected solid during vacuum filtration. Why should the water and ethanol be cold?
Please answer the question at the bottom. Fractional distillation Measure 55 mL of 40% ethanol Place 50 mL of ethanol in your distilling flask taking care that no liquid enters the side arm. Place the remaining 5 mL of ethanol in a test tube and set aside for procedure 2. Add a few marble or porcelain chips to the distilling flask to prevent bumping. Bumping is a term given to irregular boiling Assemble the rest of the apparatus for a simple distillation set-up. You may ask assistance from your instructor Cover the top of the distilling flask with a cork fitted with a thermometer. Make sure that the tip of the thermometer bulb is just below the side arm of the distillation flask Check all connections for tightness Heat the contents of the flask to boiling. Adjust the flame when the sample is already boiling. Make sure that it does not boil to dryness. Note the temperature of the first drop. Collect 60 drops of distillate per test tube. You will need 5 test tubes, thus five…
Consider the following three compounds:a. Which compound do you predict should be the most soluble in H2O? Explain.b. Which compound do you predict should have the lowest surface tension? Explain.c. Which compound should travel the lowest on a TLC plate using silica? Three compounds are HF, CF4, and CH2F2
Please write the state of matter after each compound. Also write clearly please.
In which option is the order showing whether the questions given below are true or false? () If the impurities are volatile, they can be separated according to the boiling point differences using the "Fractional Distillation" method. () If the liquid to be purified has a high boiling point, it should be done under low pressure so that the process can be carried out in a short time and does not decompose with high temperature. () Water vapor distillation is a technique used in the purification or separation of resinous substances that degrade at high temperatures. () In the crystallization process, the solubility of the substance to be purified in hot solvent should be very high, but it should not dissolve in cold and impurities should be at least moderately soluble in cold solvent. A. Right, Wrong, Right, WrongB.Wrong, Wrong, Right, RightC.Right, Wrong, Right, RightD. Wrong, Right, Right, WrongE. Wrong, Right, Right, Right
Can you show me how to solve this Experiment 3: Wet granulation Rx Calcium carbonate 135 mg Sig. Prepare 5 tabletsMagnesium carbonate 100 mgSodium chloride 50 mg10% Starch paste qsMagnesium stearate 1%Dried cornstarch 1%* The prescription is to be prepared as follows: 1. Prepare the 10% starch paste by making a slurry with a small amount of water. To this slurry, add boiling water to the final volume and stir until a translucent gel has formed.2. In a mortar, blend the calcium carbonate, magnesium carbonate and sodium chloride. Gradually with kneading and mixing, add the starch paste until a mass is formed that willball and stick together when squeezed, but will not be sticky and gummy.3. Pass this mass through sieve # 40 and collect on a paper-lined tray. Dry the granulation in the oven set at 55 degrees Celsius then pass through sieve #40 again then weigh.4. Calculate the weight of lubricant to be added (mixture equal amounts of dried cornstarch and magnesium stearate) then blend.5.…
If we are recrystallizing a PURE compound, what will happen to the sample if we cool the solution rapidly, i.e., placing it on an ice bath without cooling it first at room temperature? Note: kindly disregard the effect of rapid cooling on the container used.
2) Explain why it is common practice to determine a melting point on an unknown compound rapidly first, and then to rerun the melting point slowly.