circuit below, Vs = 41V, R1 = 130, R2 = 70, R3 = 90, R4 = 270, R5 = 160N, R6 = 1 4 as the load resistor use the Thevenin equivalent circuit to find the power dissipated in RTH, give your answer in Watts with 3 significant Only enter the number, no units. If necessary use scientific notation in the form 1200 = 1.20e3. R1 R4 R2 R5 R3 R6

circuit below, Vs = 41V, R1 = 130, R2 = 70, R3 = 90, R4 = 270, R5 = 160N, R6 = 1 4 as the load resistor use the Thevenin equivalent circuit to find the power dissipated in RTH, give your answer in Watts with 3 significant Only enter the number, no units. If necessary use scientific notation in the form 1200 = 1.20e3. R1 R4 R2 R5 R3 R6

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the DC Circuits lab , "Ohm's Law", the resistance of the four load were measured and also their accepted values were calculated: For Load A: Resisitance=4.4 kΩ (accepted value) caluculated using formula =R= R1+ R2 + R3 Resisitance=4.42kΩ (experimental value) For Load B: Resisitance=0.47 kΩ (accepted value) caluculated using formula =R= 1/(1/R1+ 1/R2 + 1/R3) Resisitance=0.47kΩ (experimental value) For Load C: Resisitance=1.95 kΩ (accepted value) caluculated using formula =R= R1+(( R2*R3)/R2 +R3) Resisitance=1.95kΩ (experimental value) For Load D: Resisitance=1.08 kΩ (accepted value) caluculated using formula =R= ((R1+ R2)* R3)/R1+R2+R3 Resisitance=1.08kΩ (experimental value) Percent Discrepancy for each load were 0 What's the conclusion then?
As shown in the Figure , an external load resistor, R, is connected across the terminal a-b of the DC circuit. Based on Norton’s Theorem, calculate and analyse the circuit shown in the figure ( given V1=60V, V2=20V, R1 = 22ohm, R2 = 34ohm, R3 = 35ohm, R4 = 42ohm,) to determine the current, i, when R = 200 Ω
1-)In the circuit given in Figure, using the YA node voltages method, V1, V2, V3, and V4 using the method of node voltages OR mesh currents I1, I2, I3calculate. 2-)Calculate the power of the 2V voltage source to indicate whether it is active (generating power) or passive(consuming power). y=4
R1 = 1 kohms R2 = 1.4 kohms R3 = 6.8 kohms E = 8VD1: Si, rB = 2 ohms, rR = 215 kohms D2: Si, rB = 7 ohms, rR = 590 kohmsApplying second approximations, determine: a) Current through D1 b) Voltage across D_2 c) Voltage across R_3
In the circuit below, i1 = 2.5 A, i2 = 5 A, and v1 = 60 V.Use nodal analysis to find the power supplied by 4ix dependent source
2. The mesh currents and node voltages in the circuit below are:i1(t) = 3.127 cos(wt - 47.27)i2(t) = 3.914 cos(wt - 101.99)i3(t) = 1.9 cos(wt + 37.53)vs1(t) = 130 cos(wt + 10.08)vs2(t) = 130 cos(wt - 24.98) Where w = 377 rad/sec, z4 = 9.26+21.82j, and z5 = 10.61 + 46j . Determine C2, R3, L3, andZ3 as the sum of two component in series in time domain.
Given that Vs is 75 V, R1 is 9 Ohm, R2 is 3 Ohm, R3 is 8 Ohm and R4 is 20 Ohm. Find equivalent VTh with respect to terminals a, b in the circuit shown. (Unit: V) Find equivalent RTh with respect to terminals a, b in the circuit shown. (Unit: Ohm)
Solve this question1)In concentrating solar power - central receiver, one of the following advantages is wrong comparing to parabolic troughSelect one:a. it requires less gross land area and less capital costb. None of thesec. No need for miles of tubes absorber tubes circulating HTFd. Less water usee. Achieves higher temperature and pressure2) The temperatures necessary to get sufficient efficiency to convert the earth’s heat to electrical power is:Select one:a. 160 °Cb. 230 °Cc. 130 °Cd. None of thesee. 200 °C
ANSWER SHOULD BE: V1 = 11.33V, V2 =26.67VSHOW THE STEP-BY-STEP SOLUTION
A Check point station as the appliances and loads shown in table 3.5.4. Estimate the daily load and peak load to be satisfied by a24 V PV system Table 3.5.4 Appliances, loads and period of operation - Lyp operation - S T il week hrs e [ ] week 0.5hr k Description el el Exlll Typ Coff Mac| 1500 W, 5 times a aytime e week 0.5hr T il =l weel Shrs N i N e week o 5, 20W, compact ghttim bulbs, dail, hr each [ Water pump | 100W, onceaday |7 Tahrs |
Consider the circuit segment shown in the figure below. GivenE1 = 1.94 V, E2 = 9.67 V, R1 = 36.8 kΩ, R2 = 65.9 kΩ, I1 = 34.4 µA, themagnitude of the current passing thru the second resistor is most nearly
2. Frame a priority list for supplying a load up to 2000 Mw in the given power plants Plant J: Fl = (2 + 0.003 PI) 103 k-cal/Mw-hr. P1= 500 MW Plant 2: F2 = (6.5 + 0.006 P2) 103 k-cal/Mw-hr P2 max = 300 MW Plant 3: F3 = (6 + 0.005 P3) 103 k-cal/Mw-hr P3 max = 240 MW The fuel costs at the plants are given by CP I=0.92 RO/kcal CP2 = 1.05 RO/kcal CP3 = 1.2 RO/kcal