Circuit Problem and Description: Using the given components, design a pneumatic circuit which will correctly and safely operate this machine control application. This is a simple two- cylinder sequence (A and B), as follow; A+ B+ A- B-. This is known as a simple sequence when the order for the cylinder to move out is the same as for cylinder to move back. The start-up signal will be by means of a normally closed 3/2 way valve operated by push button (M1) or normally closed 3/2 way valve operated by switch (M2). Full extension and retraction of each cylinder can be monitored by four normally closed 3/2 way valve operated by roller (M3-M6). Extension and retraction speeds of both cylinders must be adjustable using 2 sets of 2 single-direction flow regulation valves. Materials: Part # Component Description Quantity SAI 2026 Double acting cylinder SAI 2015 Normally closed 3/2 way valve operated by push button SAI 2016 Normally closed 3/2 way valve operated by switch SAI 2013 Normally closed 3/2 way valve operated by roller SAI 2024 Pneumatically piloted 5/2 way bistable valve SAI 2006 "AND" logic function valve SAI 2007 "OR" logic function valve SAI 2031 Set of 2 single-direction flow regulation valves 1 1 4 1 1

Circuit Problem and Description: Using the given components, design a pneumatic circuit which will correctly and safely operate this machine control application. This is a simple two- cylinder sequence (A and B), as follow; A+ B+ A- B-. This is known as a simple sequence when the order for the cylinder to move out is the same as for cylinder to move back. The start-up signal will be by means of a normally closed 3/2 way valve operated by push button (M1) or normally closed 3/2 way valve operated by switch (M2). Full extension and retraction of each cylinder can be monitored by four normally closed 3/2 way valve operated by roller (M3-M6). Extension and retraction speeds of both cylinders must be adjustable using 2 sets of 2 single-direction flow regulation valves. Materials: Part # Component Description Quantity SAI 2026 Double acting cylinder SAI 2015 Normally closed 3/2 way valve operated by push button SAI 2016 Normally closed 3/2 way valve operated by switch SAI 2013 Normally closed 3/2 way valve operated by roller SAI 2024 Pneumatically piloted 5/2 way bistable valve SAI 2006 "AND" logic function valve SAI 2007 "OR" logic function valve SAI 2031 Set of 2 single-direction flow regulation valves 1 1 4 1 1

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter53: The 555 Timer

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

The automatic washing machine system is an example of ........... loop system.
An incremental optical encoder coupled to a robot wheel has 2880 slots. Find: a) change in angle when 1200 pulses counts are obtained b) number of pulse counts when the angular change is 5000 degrees
Example 1.1 Figure 1.5 shows the block diagram of a closed-loop flow control system. Identify the following elements: (a) the sensor, (b) the transducer, (c) the actuator, (d) the transmitter, (e) the controller, (f) the manipulated variable, and (g) the measured variable. In the figure above, the (a) sensor is labeled as the pressure cell. The (b) transducer is labeled as the converter. However, there are two converters: one for converting pressure to current, and another converting current to pressure for operating the actuator. The (c) actuator is labeled as the pneumatic valve. The (d) transmitter is labeled as the line driver. The (e) controller is labeled as the PLC. The (f) manipulated variable is labeled as the pressure developed by the fluid flowing through the orifice plate. The (g) measured variable is the flow rate of the liquid.
For a 1-degree-of-freedom robot arm, it is needed to use a DC motor. Draw a blockdiagram for a mechatronic system that controls the position of this robotic arm forgripping objects. Suggest a sensor system and clarify the flow and nature of signals inyour block diagram.
Means that data concerning the effects of the computers commands are fed back to the computer as an input signal.
18- A)Define the following(i) Sensitivity (ii) Transfer function of closed loop control system
For the following automatic control systems commonly encountered in daily life, identify the devices that perform the measurement (M), decision (D), and action (A) functions, and classify the action function as “On/Off’ or “Regulating” (time-varying until reaching a setpoint). Also, draw a sketch of the control loop for each system and determine whether the control is feedback or feedforward. Automatic sprinkler system for fires Automobile cruise speed control Refrigerator
(Can someone help me with this just need a P&ID solution meeting the requirements and explanation. thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 1:Cold liquid continuously flow in a tank where its temperature is maintained at 90° C.Steam passes through the tubing which supplies energy for heating. Requirements: One feedback solution One feedforward solution PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution PROCESS 3: Product is charged in a closed, jacketed reactor where it is stirred. The reactortemperature is controlled through the uninterrupted flow of coolant in the…
Using "Subjective Digital Design", please develop the Boolean equation for the problem statement given: This CNC machine controller allow operation (represented by O) of the machine if there is a part in the vice (determined by a sensor P) and the spindle is fully retracted (determined by another sensor R) or a manual override (M) button is pressed by the operator.
Write an AVR program using the timer to generate a square wave at a frequency of 50KHz knowing that the main frequency of the microcontroller XTAL is 5MHz
Hello, i am asked to create my own statics problem, these are the specifications. Thank you very much!
Design a digital lag compensator for the position control system below to meet thefollowing specifications:ess = 0.0062 in response to a unit ramp reference input, andMp ≤ 0.095 for a unit step reference input.