(CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L= 3 ft A = 0.5 in? E = 29 x 10° psi 4 ft Aluminum L= 4 ft A = 0.75 in? E = 10 x 10 psi + 2 ft → 2 ft O a =48335 Ob 41535 Oc -55135 Od =67375 Oe 56155 Of. 57855 Og =53775 Oh =61935

(CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L= 3 ft A = 0.5 in? E = 29 x 10° psi 4 ft Aluminum L= 4 ft A = 0.75 in? E = 10 x 10 psi + 2 ft → 2 ft O a =48335 Ob 41535 Oc -55135 Od =67375 Oe 56155 Of. 57855 Og =53775 Oh =61935

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.3P: A square aluminum bar with pinned ends carries a load P = 25 kips acting at distance e = 2,0 in....

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A square aluminum bar with pinned ends carries a load P = 25 kips acting at distance e = 2,0 in. from the center (sec figure). The bar has a length E = 54 in. and modulus of elasticity E = 10,600 ksi. If the stress in the bar is not to exceed 6 ksi, what is the minimum permissible width bminof the bar?
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
Select a steel wide-flange column of a nominal depth of 360 mm (W 360 shape) to support an axial load P = 1100 kN (see figure). The column has pinned ends and length L = 6 m. Assume E = 200 GPa and y= 340 MPa. Note: The selection of columns is limited to those listed in Table F-l(b), Appendix F.
A prismatic bar with a length L = 3 ft and cross-sectional area A = 8 in2 is compressed by an axial centroidal load P = 10 kips. Determine the complete state of stress acting on an inclined section pq that is cut through the bar at an angle W = 35", and show the stresses on a properly oriented stress element.
A flying but tress transmit s a load P = 25 kN, acting at an angle of 60º to the horizontal, to the top of a vertical buttress AB (see figure). The vertical buttress has height h = 5.0 m and rectangular cross section of thickness t = 1.5 m and width b = 1.0 m (perpendicular to the plane of the figure). The stone used in the construction weighs y = 26 kN/m3. What is the required weight W of the pedestal and statue above the vertical buttress (that is, above section A) to avoid any tensile stresses in the vertical buttress?
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 2,6 m, 2.8 m, 3.0 m, and 3.2 m. The column has an outside diameter d = 140 mm and wall thickness t = 7 mm, (Assumed = 200 GPa and ( y= 250 MPa.)
A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship: