COMPARE the: a. phase diagram of eutectic point between binary system of menthol and camphor and b. phase diagram of the theoretical eutectic points. (handwritten diagram) what were the factors that could have affected the results? provide recommendations on how to increase the accuracy/correctness of data

COMPARE the: a. phase diagram of eutectic point between binary system of menthol and camphor and b. phase diagram of the theoretical eutectic points. (handwritten diagram) what were the factors that could have affected the results? provide recommendations on how to increase the accuracy/correctness of data

Macroscale and Microscale Organic Experiments

7th Edition

ISBN:9781305577190

Author:Kenneth L. Williamson, Katherine M. Masters

Publisher:Kenneth L. Williamson, Katherine M. Masters

Chapter5: Distillation

Section: Chapter Questions

Problem 4Q

See similar textbooks

Similar questions

10.11/ A 1.5-kg specimen of a 90 wt% Pb-10 wt% Sn alloy is heated to 250°C (480°F), at which temperature it is entirely an a-phase solid solution . The alloy is to be melted to the extent that 50% of the speci- men is liquid, the remainder being the a phase. This may be accomplished either by heating the alloy or changing its composi- tion while holding the temperature con- stant. (a) To what temperature must the speci- men be heated? (b) How much tin must be added to the 1.5-kg specimen at 250°C to achieve this state? 10.15) A magnesium-lead alloy of mass 5.5 ka consists of a solid a phase that has a compo- sition that is just slightly below the solubility limit at 200°C (390°F). (a) What mass of lead is in the alloy? (b) If the alloy is heated to 350°C (660°F). how much more lead may be dissolved in the a phase without exceeding the solubility limit of this phase? 10.27 A hypothetical A-B alloy of composition 55 wt% B-45 wt% A at some temperature is found to consist of mass…
Polyethylene glycol 400 (PEG400) is a nonvolatile liquid polymer, which when mixed with water canbe used as a base for parenteral formulations. The designation “400” means that the molecular weightof PEG molecules is approximately 400 g/mol. Preparation with water (ΔHv = 40.7 kJ/mol) requires that the two be mixed at 56 oC, at which the equilibrium vapor pressure of pure water is 16.5 kPa. a. If 105 g of PEG400 are added to 500 g of water at 56 oC, what will the boiling temperature of the solution be?
Match the following: Freezing point depressionThe effect of supercoolingFreezing point of pure solventRegion where liquid is coolingRegion where liquid is freezing I have attached a picture for this question. I guessed the answers to be B,D,E,F,A but i am not sure if it is correct
Define the relative amounts of liquid and vapor phases in a saturated mixtureare specified by the quality x.
The osmotic pressure of a solution of polystyrene in toluene (methylbenzene} was measured at 25 °C with the following results:c/(g dm-3) 2.042 6.613 9.521 12.602∏/Pa 58.3 188.2 270.8 354.6Determine the molar mass of the polymer.
What is the amount of energy required (in KJ) to convert 100g of ice at -20 degrees to steam vapour at 120 degrees? If the total amount of surfactant to be used in an emulsion is 5g, calculate the amount of Span 80 (HLB=4.3) and Tween (HLB =16.7) in order to obtain an HLB value of 9.5
A solution of common salt in water is prepared by adding 50kg of salt to 200kg of water tomake a liquid density of 1250kg/m3. Calculate the concentration of salt in this solution as a: i) Weight(w/w)fraction (Ans: weight fraction 20%)
Determine the boiling point elevation of 5 m ("molal") NaOH in ⁰C. Ebuillioscopic constant of the solvent used is 0.7 ⁰C/m.
The table below shows temperature/composition data collected for a mixture of methylbenzene (M) and octane (O) at 1 atm. Recall that x stands for the mole fraction in the liquid and y stands for the mole fraction in the vapor in equilibrium. The boiling points for methylbenzene (M) and octane (O) are 110.60C and 125.60C, respectively. Construct the phase diagram with Temperature vs. xM. What is the composition of the vapor in equilibrium with the liquid of composition (a) xM = 0.250 and (b) xO = 0.250. T (0C) 110.9 112.0 114.0 115.8 117.3 119.0 121.1 123.0 xM 0.908 0.795 0.615 0.527 0.408 0.300 0.203 0.097 yM 0.923 0.836 0.698 0.624 0.527 0.410 0.297 0.164
Referring to the Al-Si Eutectic diagram discussed on the Phase Diagrams-Lever Rule handout, calculate the mass fraction of the phase, silicon, given a sample with 51.7 wt% aluminum at 576.99 ˚C.
The following molarities were calculated from replicate standardization of a solution: 0.5022, 0.5022, 0.5021, 0.5008, upper limit of the 95% confidence interval?
For a given liquid a plot of the lnP versus 1/T gives a straight line with a slope of -2829 K.What is the ΔHvap of this liquid? Your answer should be in kJ/mol and have 3 sig figs