Consider a flow over a surface with the velocity and temperature profiles given as u(v) = C1 (y + y² – y' ) T(y) = C2 – e-2C,y where the coefficients Ci and C2 are constants. Determine the expressions for the friction coefficient ( Cf ) and the convectionheat transfer coefficient (h). Define apropriate boundary conditions for C1 and C2 solution.

Consider a flow over a surface with the velocity and temperature profiles given as u(v) = C1 (y + y² – y' ) T(y) = C2 – e-2C,y where the coefficients Ci and C2 are constants. Determine the expressions for the friction coefficient ( Cf ) and the convectionheat transfer coefficient (h). Define apropriate boundary conditions for C1 and C2 solution.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.38P

See similar textbooks

Similar questions

5.7 The average Reynolds number for air passing in turbulent flow over a 2-m-long, flat plate is . Under these conditions, the average Nusselt number was found to be equal to 4150. Determine the average heat transfer coefficient for an oil having thermal properties similar to those in Appendix 2, Table 18, at at the same Reynolds number and flowing over the same plate.
Hot engine oil at 150°C is flowing in parallel over a flat plate at a velocity of 2 m/s. Surface temperature of the 0.5-mlong flat plate is constant at 50°C. Determine (a) the local convection heat transfer coefficient at 0.2 m from the leading edge and the average convection heat transfer coefficient, and (b) repeat part (a) using the Churchill and Ozoe (1973) relation.
Please help with this questionHot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. Thegas at 220°C flow is parallel over the upper and lower surfaces of a 3-m-longflat plate at a velocity of 3 m/s. If the flat plate surface temperature ismaintained at 80°C.Determine the local convection heat transfer coefficient at 1 m fromthe leading edge and calculate the average convection heat transfer coefficient over theentire plate.
Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the Colburn, Petukhov, and Gnielinski equations, determine the Nusselt numbers for Reynolds numbers at 3500, 104, and 5 * 105. Compare and discuss the results.
1. Experimental analysis was carried out about turbulent convective heat transfer in trapezoidal cross-sectioned duct.Average Nusselt numbers and Reynolds numbers were determined for each experiment and the following data set have beenobtained from this investigation. Find an engineering correlation between the average Nusselt number and Reynolds numberin the form ofNu = aReb
Liquid mercury at 250°C is flowing with a velocity of 0.3 m/s in parallel over a 0.1-m-long flat plate where there is an unheated starting length of 5 cm. The heated section of the flat plate is maintained at a constant temperature of 50°C. Determine (a) the local convection heat transfer coefficient at the trailing edge, (b) the average convection heat transfer coefficient for the heated section, and (c) the rate of heat transfer per unit width for the heated section.
Air (1 atm) enters into a 5-cm-diameter circular tube at 20°C with an average velocity of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the outlet mean temperature is 80°C. Estimate the length of the tube.
A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is ?
Liquid mercury is flowing at 0.6 kg/s through a 5-cm-diameter tube with inlet and outlet mean temperatures of 100°C and 200°C, respectively. The tube surface temperature is maintained constant at 250°C. Determine the tube length using (a) the appropriate Nusselt number relation for liquid metals and (b) the Dittus–Boelter equation. (c) Compare the results of (a) and (b).
Hot carbon dioxide exhaust gas at 1 atm is being cooled by flat plates. The gas at 220oC flows in parallel over the upper and lower surfaces of a 1.5-m-long flat plate at a velocity of 3m/s. if the flat plate surface temperature is maintained at 80oC, determine (a) the local convection heat transfer coefficient at 1 m from the leading edge, (b) the average convection heat transfer coefficient over the entire plate, and (c) the total heat flux transfer to the plate.
Water at 15°C is to be heated to 65°C by passing it over a bundle of 4-m-long, 1-cm-diameter resistance heater rods maintained at 90°C. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods are arranged in-line with longitudinal and transverse pitches of SL=4 cm and ST=3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise. Please, I need the solution from fundamental concepts of how the heat flow behaves in the system. That it be answered with theory of the subject
Water at 15ºC is to be heated to 65ºC by passing it over a bundle of 4-m-long 1-cm-diameter resistance heater rods maintained at 90ºC. Water approaches the heater rod bundle in normal direction at a mean velocity of 0.8 m/s. The rods arc arranged in-line with longitudinal and transverse pitches of SL 4 cm and ST 3 cm. Determine the number of tube rows NL in the flow direction needed to achieve the indicated temperature rise.