Consider a step shaft fixed at both ends and loaded with a torsional moment M., as shown in Figure Q.3. (a) Determine the maximum value of the torsional moment M. if the maximum shear stress (allowable stress) is given as 130 MPa. (b) Determine the angle of twist of one end with respect to the other end.

Consider a step shaft fixed at both ends and loaded with a torsional moment M., as shown in Figure Q.3. (a) Determine the maximum value of the torsional moment M. if the maximum shear stress (allowable stress) is given as 130 MPa. (b) Determine the angle of twist of one end with respect to the other end.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.11.5P: A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used...

See similar textbooks

Similar questions

A thin-walled rectangular tube has uniform thickness t and dimensions a x b to the median line of the cross section (see figure). How does the shear stress in the tube vary with the ratio = a/b if the total length Lmof the median line of the cross section and the torque T remain constant? From your results, show that the shear stress is smallest when the tube is square (ß = 1).
The steel axle of a large winch on an ocean liner is subjected to a torque of 1.65 kN · m (see figure). What is the minimum required diameter dminif the allowable shear stress is 48 M Pa and the allowable rate of twist is 0.75º/m? (Assume that the shear modulus of elasticity is 80 G Pa.) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d/8, Compare dminvalues to corresponding values from part (a)
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
A square tube section has side dimension of 20 in. arid thickness of 0.5 in. If the section is used for a 10-ft-long beam subjected to 1250 kip-in, torque at both ends, calculate the maximum shear stress and the angle of twist between the ends. Use G = 11,600 ksi.
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Angle of Twist in degrees?
Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively. The material has-a shear modulus of 60 kN/mm'. Determine the maximum stress in the shaft when it is subjected to a twist of 5 in a length of 2.5 m. What is the maximum torque the shaft can carry? For a circle / = nd*/32.
The wrench is applied to two forces each of magnitude P. The steel shaft AB has a diameter of 15 mm. If the shear stress in the shaft is not exceed 120 MPa and the angle of twist is not exceed 5; find the largest allowable of P. For steel; use G = 80 GPa.
Find the maximum stress developed in a stepped shaft when it is subjected to a: i) Torque of “T” Nm. ii) Bending moment of “M” Nm. r = 5 mm D = 50 mm d = 25 mm Torque “T” Nm = 150 Bending moment ‘’M’’ Nm = 250
A solid circular shaft has a diameter of d mm and is made from steel, which fail when tested in simple tension test at a stress of 150 MPa. The shaft was subjected by bending moment and torque which are 22.2 kNm and 44.4 kNm respectively. Calculate the minimum allowable shaft diameter, d according to:- (a) Tresca failure criterion (b) Von Mises theory of elastic failure
two solid steel shafts of different diameters are joined together at point C. the diameter of the smaller shaft is 0.5 in, while the diameter of the larger shaft is 1 in. if the supports at both ends, A & B, are unyielding / rigid, and a counterclockwise torque of 500 ft lb at point D, determine the maximum shear stress in the shaft in ksi. The modulus of rigidity for steel is 10800 ksi.Show full solution please