Consider an ordinary shower where hot water at 140°F is mixed with cold water at 50°F. If it is desired that a steady stream of warm water at 110°F be supplied, determine the ratio of the mass flow rates of the hot to cold water. Assume the heat losses from the mixing chamber to be negligible and the mixing to take place at a pressure of 20 psia.

Consider an ordinary shower where hot water at 140°F is mixed with cold water at 50°F. If it is desired that a steady stream of warm water at 110°F be supplied, determine the ratio of the mass flow rates of the hot to cold water. Assume the heat losses from the mixing chamber to be negligible and the mixing to take place at a pressure of 20 psia.

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter1: Temperature And Heat

Section: Chapter Questions

Problem 22CQ: If you place 0 ice into 0 water in an insulated container, what will the net result be? Will there...

See similar textbooks

Similar questions

For a temperature increase of 10 at constant volume, what is the heat absorbed by (a) 3.0 mol of a dilute monatomic gas; (b) 0.50 mol of a dilute diatomic gas; and (c) 15 mol of a dilute polyatomic gas?
If you place 0 ice into 0 water in an insulated container, what will the net result be? Will there be less ice and more liquid water, or more ice and less liquid water, or will the amounts stay the same?
In a one-shell and two-tube heat exchanger, cold water with inlet temperature of 20°C is heated by hot water supplied at the inlet at 80°C. The cold and hot water flow rates are 5000 kg/h and 10,000 kg/h, respectively. If the shelland- tube heat exchanger has a UAs value of 11,600 W/K, determine the cold water and hot water outlet temperatures. Assume cpc = 4178 J/kg·K and cph = 4188 J/kg·K.
Water enters a 2.5-cm-internal-diameter thin copper tube of a heat exchanger at 15°C at a rate of 0.3 kg/s, and is heated by steam condensing outside at 120°C. If the average heat transfer coefficient is 800 W/m2·°C, determine the length of the tube required in order to heat the water to 115°C
A test is conducted to determine the overall heat transfer coefficient in anautomotive radiator that is a compact cross-flow water-to-air heat exchangerwith both fluids (air and water) unmixed. The radiator has 40 tubesof internal diameter 0.5 cm and length 65 cm in a closely spaced plate-finnedmatrix. Hot water enters the tubes at 90°C at a rate of 0.6 kg/s and leaves at65°C. Air flows across the radiator through the interfin spaces and is heatedfrom 20°C to 40°C. Determine the overall heat transfer coefficient Ui of thisradiator based on the inner surface area of the tubes.
Saturated steam at 1 atm condenses on a vertical plate that is maintained at 90°C by circulating cooling water through the other side. If the rate of heat transfer by condensation to the plate is 180 kJ/s, determine the rate at which the condensate drips off the plate at the bottom.
A 2-m * 1.5-m section of wall of an industrial furnaceburning natural gas is not insulated, and the temperatureat the outer surface of this section is measured to be 80°C.The temperature of the furnace room is 30°C, and the combinedconvection and radiation heat transfer coefficient at thesurface of the outer furnace is 10 W/m2·K. It is proposed toinsulate this section of the furnace wall with glass wool insulation(k = 0.038 W/m·K) in order to reduce the heat lossby 90 percent. Assuming the outer surface temperature ofthe metal section still remains at about 110°C, determine thethickness of the insulation that needs to be used.The furnace operates continuously and has an efficiency of78 percent. The price of the natural gas is $1.10/therm (1 therm =105,500 kJ of energy content). If the installation of the insulationwill cost $250 for materials and labor, determine how long it willtake for the insulation to pay for itself from the energy it saves.
Consider a 6-in * 8-in epoxy glass laminate (k = 0.10 Btu/h·ft·°F) whose thickness is 0.05 in. In order to reduce the thermal resistance across its thickness, cylindrical copper fillings (k = 223 Btu/h·ft·°F) of 0.02 in diameter are to be planted throughout the board, with a center-to-center distance of 0.06 in. Determine the new value of the thermal resistance of the epoxy board for heat conduction across its thickness as a result of this modification.
Consider a 3-m-high rectangular enclosure consisting of two surfaces separated by a 0.1-m air gap at 1 atm. If the surface temperatures across the air gap are 30°C and –10°C, determine the ratio of the heat transfer rate for the horizontal orientation (with hotter surface at the bottom) to that for vertical orientation.
A counter-flow double-pipe heat exchanger is to heat water from 20°C to 80°C at a rate of 1.2 kg/s. The heating is to be accomplished by geothermal water available at 160°C at a mass flow rate of 2 kg/s. The inner tube is thin-walled and has a diameter of 1.5 cm. If the overall heat transfer coefficient of the heat exchanger is 640 W/m2?K, determine the length of the heat exchanger required to achieve the desired heating.
Solar radiation is incident on a 5 m2 solar absorberplate surface at a rate of 800 W/m2. Ninety-three percent ofthe solar radiation is absorbed by the absorber plate, whilethe remaining 7 percent is reflected away. The solar absorberplate has a surface temperature of 40°C with an emissivityof 0.9 that experiences radiation exchange with the surroundingtemperature of -5°C. In addition, convective heat transferoccurs between the absorber plate surface and the ambientair of 20°C with a convection heat transfer coefficient of7 W/m2∙K. Determine the efficiency of the solar absorber,which is defined as the ratio of the usable heat collected bythe absorber to the incident solar radiation on the absorber.
Estimate the rate at which heat can be conducted from theinterior of the body to the surface. As a model, assume thatthe thickness of tissue is 4.0 cm, that the skin is at 34°Cand the interior at 37°C, and that the surface area is 1.5m2Compare this to the measured value of about 230 W thatmust be dissipated by a person working lightly. This clearlyshows the necessity of convective cooling by the blood