Water vapor enters an adiabatic turbine with a pressure of 7 MPa and a flow rate of 2kg / sec at a temperature of 400 ° C, expanding up to 20 Kpa pressure. The adiabatic efficiency of the turbine is 0.8. Calculate the temperature of the steam at the turbine outlet and the power of the turbine, neglecting the kinetic and potential energy change of the steam.

Water vapor enters an adiabatic turbine with a pressure of 7 MPa and a flow rate of 2kg / sec at a temperature of 400 ° C, expanding up to 20 Kpa pressure. The adiabatic efficiency of the turbine is 0.8. Calculate the temperature of the steam at the turbine outlet and the power of the turbine, neglecting the kinetic and potential energy change of the steam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters a turbine at 10,000 kPa and 500 °C, and exhausts at 100 °C with an enthalpy of 2000 kJ/kg. The mass flow rate is m=4.5 kg∙s-1. What is the specific volume (m3/kg) of the exiting stream?
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
Air at 90 kPa and 10oC enters an adiabatic diffuser steadily with a velocityof 180 m/s and leaves with a low velocity at a pressure of 100 kPa. Theexit area of the diffuser is 4 times the inlet area. Determine the exittemperature.
The entropy of steam entering the turbine at temperature 800°C and Pressure 1600 kPa is
Steam is accelerated as it flows through an actual adiabatic nozzle. The entropy of the steam at the nozzle exit will be (greater than, equal to, less than) the entropy at the nozzle inlet.
Water steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 4 MPa, 500oC, and 80 m/s, and the exit conditions are 30 kPa, 92 percent quality, and 50 m/s. The mass flow rate of the steam is 12 kg/s. Determine the power output. Neglect potential energy change, but not the kinetic energy change. A ) close to 23 kW B ) close to 12 kW C ) close to 23 MW D ) close to 5 MW E ) close to 12 MW F ) close to 10 MW G ) close to 5 kW H ) close to 10 kW
Steam expands isentropically in a converging/diverging nozzle from inlet conditionsof 1400 kPa, 325°C, and negligible velocity to a discharge pressure of 140 kPa. At thethroat, the cross-sectional area is 6 cm2. Determine the mass flow rate of the steamand the state of the steam at the exit of the nozzle.
Air is heated as it flows through a 6 in × 6 in square duct with negligible friction. At the inlet, air is at T1 = 700 R, P1 = 80 psia, and V1 = 260 ft/s. Determine the rate at which heat must be transferred to the air to choke the flow at the duct exit, and the entropy change of air during this process.
Air is expanded from 200 psia and 500°F to 100 psia and 50°F. Assuming constant specific heats, determine the change in the specific entropy of air
EMERGENY!!!! A perfect gas of adiabatic type expands from 1200K and 900kPa to 700k. Calculate the volumetric flow at the turbine inlet when the power generated by the turbine is 400kW. (CP=1.13kj/kg K Cu =0.83kj/kg K VE R=0.30 kj/kgK )
Steam at a temperature of 210°c has specific entropy of 7.1167 kJ/kg-K. Determine the pressure, internal energy, enthalpy and volume.
Nitrogen enters a steady-flow heat exchanger at 150 kPa, 10°C, and 100 m/s, and it receives heat in the amount of 150 kJ/kg as it flows through it. The nitrogen leaves the heat exchanger at 100 kPa with a velocity of 200 m/s. Determine the stagnation pressure and temperature of the nitrogen at the inlet and exit states.