Consider the figure below of an individual performing a leg strengthening exerCise. FM Knee R, Fs Ankle F What is the moment of force about the knee due to the quadriceps muscle force? The muscle force, F, is 1500 N. The patella ligament (which transmits the quadriceps force to the tibia) inserts 5 cm distal to the knee joint axis on the tibia at an angle, OM of 0.52 rad relative the to the shank segment. The shank segment angle (es) is 0.80 rad relative to the right hand horizontal. (Respect the coordinate system as drawn)

Consider the figure below of an individual performing a leg strengthening exerCise. FM Knee R, Fs Ankle F What is the moment of force about the knee due to the quadriceps muscle force? The muscle force, F, is 1500 N. The patella ligament (which transmits the quadriceps force to the tibia) inserts 5 cm distal to the knee joint axis on the tibia at an angle, OM of 0.52 rad relative the to the shank segment. The shank segment angle (es) is 0.80 rad relative to the right hand horizontal. (Respect the coordinate system as drawn)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the facade of a house consists of two cylindrical pillars placed at 1 m at the ends of a beam, these pillars support a steel beam of 320 kg and 6 m in length. the center of mass of the beam is at 2.8 m starting from the left end. at each end a new circular column was placed in order to raise a second floor, each of these columns has a mass of 120 kg. if it is considered that the structure must support 2100 kg distributed every 1.5 m, what will be the reaction of each column in the lower zone?
To get up on the roof, a person (mass 85.0 kg) places a 6.20 m aluminum ladder (mass 15.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The top of the ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2.00 m from the base, as measured along the ladder. The person is standing on the ladder 3.00 m from the base, as measured along the ladder. Find the normal reaction and friction forces (in N) on the ladder at its base. (Enter the magnitudes.)
A steel rod of circular section tapes from 2 cm diameter to 1 cm diameter over a length of 50 cm. If the modulus of elasticity of the material is 2*10^ 6 kg/cm^ 2 , then the increase in length under a pull of 3000 kg will be
A 50-kg barrel hangs from one end of a 30-kg beam 3.0-m long. The distance from the loaded end of the balance point is a. 94 cm b. 56 cm c. 113 cm d. 175 cm
You and your team are conducting a restoration project at an old city hall to investigatethe condition of the old chandelier at the main hall. The chandelier was estimated toweigh 4800 N and supported by three cables as shown in Figure 1. The project requiresyou to investigate the condition of the cables holding the chandelier after many years.Given the diameter of cable B is 6mm, while diameter of cable C is 1.25 times and cableA is 1.5 times of cable B, analyze the stress condition of the cables and propose a suitableinclination of the cable B to maintain the normal stress in cable C to be 0.5 times thanthe normal stress of cable B in order for the cable to support the chandelier
ENGINEERING QUESTION- SOLVE FROM SCRATCH! A mass of 450 kg has been hung from the end of a metal wire whose initial length is 1.8 meters and is 1.5 mm in diameter. If the wire is stretched 1.25 cm.a) What were the stress and strain?b) What is Young's modulus?
A 40 kg-mass hangs from the end of a uniform beam. The beam is 6.0 m long and has a mass of 60 kg. The beam is supported at the left end by a hinge at the wall and by a cable at the right end. The other end of the cable is tied to the wall at a point 4.0 m above the left end of the beam. (g = 9.81 m/s² )A. Draw the FBD;B. Find the tension (T) in the supporting cable in Newtons; andC. Find the reaction force (R) of the hinge on the beam ( magnitude and direction).
1. A non-uniform is 4.5m long and weighs 640N. It is balance when a 270N weight is hung 0.800m from the light end of the bar and the bar is pivoted at its center. Where is the center of gravity of the bar? 2.Two workers carry a non-uniform beam weighing 730N. The beam is 2.6m long and its center of gravity is 1.1 m from one end. If the workers hold the beam at its end, how much does each worker lift?
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
A dumbwaiter 3 m above floor falls freely due to sudden breakage of wire rope carrying it. A coil spring is provided below at level with floor to absorb shock. If spring deflected 30.48 cm. due to gross wright of elevator, 100 kg, determine: a. wire diameter, Dw b. mean diameter of coil, Dm c. number of active coils, Nc Use: C = 8 G = 808720 kg/cm^2
Solid steel wire (2 meters) contains a musical instrument (0.3 mm). When the wire is under tension (90N), how does its length change?
One spring is placed inside the other, not touching each other, and compressed between a pair of parallel plates until the distance between the plates is 40 mm. Make a neat detailed sketch of the spring and plate assembly. If G = 83 GPa for both springs, calculate the following: 1. The force applied to the spring assembly. 2. The shear stress induced in each spring. 3. The total strain energy stored in the spring assembly. 4. The stiffness of each spring. 5. The equivalent stiffness of a single spring that can be substituted in place of these springs.