Consider the op-amp circuit shown in Figure below, where the op amp has infinite input resistance and zero output resistance but finite open-loop gain. a) Prove that B = R1/R1 + R2. b) If R = 10 kn, find R2 that results in G = 10 V/V for the following three cases: i A= 1000 V/V %3D i. A = 200 V/V %3D i. A = 15 V/v Vo R2 RA

Consider the op-amp circuit shown in Figure below, where the op amp has infinite input resistance and zero output resistance but finite open-loop gain. a) Prove that B = R1/R1 + R2. b) If R = 10 kn, find R2 that results in G = 10 V/V for the following three cases: i A= 1000 V/V %3D i. A = 200 V/V %3D i. A = 15 V/v Vo R2 RA

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

A non-inverting op-amp circuit has the open loop gain of 136 and the resistances R1=3500 Ω and R2 = 3.8 kΩ . Calculate (a) The actual value of voltage gain (b) Considering the finite open loop gain, the ideal value of gain (c) Error, when ideal voltage gain is compared with actual voltage gain (d) The percentage error, when ideal voltage gain is compared with actual voltage gain. (a) The actual value of voltage gain Answer for part 1 (b) The ideal value of voltage gain Answer for part 2 (c) Error, when ideal voltage gain is compared with actual voltage gain. Answer for part 3 (d) The percentage error, when ideal voltage gain is compared with actual voltage gain.
In the circuit below, assuming the ideal opamp, we ask a) determine the circuit gain (Avf = V2 / V1). b) Calculate the gain value when R1 = R3 = 10KΩ and R2 = 16kΩ answer a) Avf=1((R1+R3)/R2) b) Avf=2,25
Q3. For the op-amp circuit shown below, find the value of vO, where R1 = 20 Ω, R2 = 12 Ω, R3 = 15 Ω, R4 = 19 Ω, Rf = 17 Ω, VS1 = 12 V, and VS2 = 9 V.
a.Realize a circuit to obtain Vo=5V1-2V2+3V2 using op-amp connected in an inverting mode, Where V1, V2and V3 are positive input signals connected. take the value of feedback resistors as 100ohms. b.An op-amp has a feedback resistor Rf =25kiloohms and the Rs1=6kiloohms, Rs2=10kiloohms, Rs3=5kiloohms. The corresponding inputs are Vi1=-15v, Vi2=4, Vi3=12. The non-inverting terminal is grounded. calculate the total Voltage.
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
Consider the active circuit with the schematic: (ONLY ANSWER C-E) a. Assuming it's an ideal op amp, derive the circuit’s transfer function as a function of frequency, H(jw). Make sure it in canonical form.b. We want a DC gain of 40dB. If the op amp has value of Rin = 10MΩ and Rout = 50Ω, choose appropriate values for R1 and R2. Explain why your selected values of R1 and R2 allow you to ignore Rin and Rout for the remainder of the problem. c. If L = 1H, sketch the straight-line approximation of the Bode plot for the circuit’s gain assuming the op amp can still be considered as ideal.d. The op amp you select turns out to be non-ideal, and it has a real pole at wC = 1krad/s. Write the updated transfer function for your circuit (using your values of R1, R2, and L = 1H). Make it in the canonical form.e. Sketch the straight-line approximation of the Bode plot for the circuit with your updated transfer function from D.
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100KW. R1 = R3 = 10W, R5 = 10W, R6 = 90 KW. and R5 = 10W. The load resistor R7 = 10KW. The current source; I1 = 100μA and V2 = 1V.
1. The virtual short is applicable A. If one of the input is tied to the ground B. Only if there is a feedback C. All the time D. Depending on the components used 2. What ideal characteristic of Op-Amp contributes to the Virtual Short concept? A. Zero Ohm Input Resistance B. Zero Ohm Output Resistance C. Input terminals do not let current to flow D. Infinite gain 3. Op-amp closed loop gain varies A. True B. Depending on the resistor values used C. Not applicable D. False
The input-output relationship for the inverting op amp circuit is given ideally by: Vo = (-R f / Ri)Vi . The closed loop gain of the amplifier circuit is calculated as G = Vo/Vi. Use these equations to calculate the the expected output voltage and gain of the opamp circuit given
I am asking for a solution branchs C & D Activity # 2You have to study the effect of the type of feedback on building op amp applications using 741 op-amp.A) Discuss the circuits in Figure 2 using the 741 op-amps and the biasing voltage of 10V. Assume R1 and R2 are equal. Build both circuits virtual and the lab and compare the out results having an input sinusoidal of 8V amplitude and 1kHz frequency.B) Explain the principle of operation of Figure 2. Explain limitations of both circuit in terms of practical applications. What is the technical name describing this circuit? What are the reference voltages in both circuitsC) Explain the principle of operation of the op-amp in the first stage of Figure 1. What is the advantage of this circuit compared to Circuits in Figure 2? What is the technical name describing this circuit?D) Explain the principle of operation of the op-amp in the last stage of Figure 1. What is the advantage of this circuit compared to Circuits in (A) and (C)? What…
Based on the op amp circuit in Figure, answer the following questions,assuming an ideal op-amp. Given:V1 = 1 VI2 = 2 mAV3 = 0.5 VRa = 2 kΩRb = 1 kΩRc = 5 kΩRd = 10 kΩ Determine the voltage Vx, and the current Ib through Rb
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792