R 3R 2R V1 Vout V2 Consider the network above with V; = 4V, Vz = 6V, and R= 4k2. Treat the op-amp as real, with B = 1.8 x 10°, R, = 3M2, and R, = 402. a. What is the voltage v, across the input teminals? b. What is the current i, through the input teminals? c. What is the "ideal" output voltage (treating the op-amp as ideal)? Videal d. What is the difference between the ideal and real output voltage? Vreal - Videal

R 3R 2R V1 Vout V2 Consider the network above with V; = 4V, Vz = 6V, and R= 4k2. Treat the op-amp as real, with B = 1.8 x 10°, R, = 3M2, and R, = 402. a. What is the voltage v, across the input teminals? b. What is the current i, through the input teminals? c. What is the "ideal" output voltage (treating the op-amp as ideal)? Videal d. What is the difference between the ideal and real output voltage? Vreal - Videal

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Q2. For the op-amp circuit as shown below, given that RS = 50.5 kΩ, RL = 9 kΩ, R1 = 10 kΩ, R2 = 11 kΩ, R3 = 6 kΩ, R4 = 4 kΩ, R5 = 1.8 kΩ. (a) Determine the voltage gain G1=vO1/vS: (b) Determine the voltage gain G2=vO/vS:
Q3. For the op-amp circuit shown below, find the value of vO, where R1 = 20 Ω, R2 = 12 Ω, R3 = 15 Ω, R4 = 19 Ω, Rf = 17 Ω, VS1 = 12 V, and VS2 = 9 V.
For the circuit below, use superposition to find vO in terms of the input voltages v1 and v2. Assume an ideal op amp. v1= 8sin(2??x60t)- 0.1sin(2??x5000t) volts and v2 =8sin(2??x60t) +0.1sin(2??x5000t) volts
For the op-amp circuit as shown below, given that RS = 46 kΩ, RL = 15 kΩ, R1 = 15 kΩ, R2 = 11 kΩ, R3 = 6.5 kΩ, R4 = 2.5 kΩ, R5 = 3 kΩ.
In the circuit below, assuming the ideal opamp, we ask a) determine the circuit gain (Avf = V2 / V1). b) Calculate the gain value when R1 = R3 = 10KΩ and R2 = 16kΩ answer a) Avf=1((R1+R3)/R2) b) Avf=2,25
You are given the following circuit. Assume that V1 = 4 V, V2 = 6.8 V, V3 = 4.9 V, V4 = 7.2 V, V5 = 7.6 V, R1 = 97 kΩ, R2 = 26 kΩ, R3 = 46 kΩ, R4 = 49 kΩ, and R5 = 40 kΩ. What is the voltage vn at the inverting terminal of the op-amp?
For the circuit configuration below with R1 =6Ω, R2 =5Ω,R3 =4Ω, R4 =7Ω, R5 =15Ω, R6 =16Ω, vg=27V, with ideal op-amps, calculate v0.
Figure Q. 3(b) shows an op amp circuit for linear amplifier application. (i) Determine the value of current I3.(ii) Find the value of R if the output current, Io is given as 2 mA.(iii) Explain what will happen to output voltages, V01 and V02 if the supplyvoltages, +VCC and -VCC are connected to +10V and -10V.
Find the relationship between the output and the input in the amplifier circuit depicted in Figure Q3.a & Q3.2. State any assumptions you make. [Derive the formula of gain]
Obtain the transfer function Eo(s)/Ei(s) of the op-amp system shown in Figure 3–27 in terms ofcomplex impedances Z1 , Z2 , Z3 , and Z4 . Using the equation derived, obtain the transfer functionEo(s)/Ei(s) of the op-amp system shown in Figure 3–26
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100 kiliohm. R1 = R3 = 10 kiliohm, R5 = 10 kiliohm, R6 = 90 kiliohm. and R5 = 10 kiliohm. The load resistor R7 = 10 kiliohm. The current source; I1 = 100μA and V2 = 1V.
The following Operational Amplifier circuit is given. Analyze the circuit carefully to identify the functions (i.e., OP-AMP configurations) of each OP-Amps. Calculate the first stage output voltage Vx and then the output voltage at the output of the second stage Vo . Determine the currents I0, IF, and IX . Finally, determine the power absorbed by the resistor R7. The resistors: R2 = R4 =100KW. R1 = R3 = 10W, R5 = 10W, R6 = 90 KW. and R5 = 10W. The load resistor R7 = 10KW. The current source; I1 = 100μA and V2 = 1V.