Consider the refrigerator shown in Figure. If the compressor consumes 850 W of power and the COP of the refrigerator is 2.5 determine. The mass flow rate of the refrigerant The rate of heat rejected to the kitchen air Condenser Expansion valve Win Compressor Evaporator 100 kPa x0.2 100 kPa Qu -26°C

Consider the refrigerator shown in Figure. If the compressor consumes 850 W of power and the COP of the refrigerator is 2.5 determine. The mass flow rate of the refrigerant The rate of heat rejected to the kitchen air Condenser Expansion valve Win Compressor Evaporator 100 kPa x0.2 100 kPa Qu -26°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A heat engine receives heat from a source at 1100 K at a rate of 400 kJ/s, and it rejects the waste heat to a medium at 320 K. The measured power output of the heat engine is 120 kW, and the environment temperature is 25°C.Determine the reversible power.
A steady-flow thermodynamic system receives 100 lb/min of fluid at 30 psia and 200 Fahrenheit and discharges it from a point 80 ft above the entrance section at 150 psia and 600 Fahrenheit. The fluid enters with velocity of 1200 fpm and leaves with a velocity of 200 fpm. During this process, there are supplied 25,000 Btu/hr of heat from an external source and the increase in enthalpy is 2 Btu/lb. Determine the work done in horsepower.
In an adiabatic turbine, this steam flow is 50 kg / s. The power produced by the turbine is 29 MW.Steam enters the turbine with a pressure of 50 bar and a speed of 60 m / s. At the outlet, at a pressure of 0.06 barIt comes out as saturated water with a speed of 130 m / s. Accordingly, the heat lost by the turbine andFind the turbine inlet and outlet temperatures of steam
Refrigerant-134a enters the condenser of a residential heat pump at 800 kPa and 35°C at a rate of 0.018 kg/s and leaves at 800 kPa as a saturated liquid. If the compressor consumes 1.2 kW of power, determine the rate of heat absorption from the outside air.
Refrigerant R-134a at 400 kPa and 10 x 1 ⁰C (if last digit is 2 then 10 x 2 = 20 ⁰C)enters an adiabatic diffuser steadily with a velocity of 600 m/s and leaves at 600 kPa and 100⁰C. Determine:a) The exit velocityb) The inlet to exit area ratioc) The inlet exit density ratio
A steady-flow thermodynamic system receives 100 lbm/min of fluid at 30 psia and 2 ft^3/lbm and discharges it from a point 80 ft above the entrance section at 150 psia and 0.5 ft^3/lbm. The fluid enters with velocity of120 ft/sec and leaves with a velocity of 40 ft/sec. During this process, there are supplied 25,000 Btu/hr of heat from an external source. Change of internal energy is neglected. Determine the work done Btu/lbm and power in hp.
Refrigerant-134a at 1 MPa and 90 degrees * C is to be cooled to 1 MPa and 30 degrees * C in a condenser by air. The air enters at 100 kPa and 27°C with a volume flow rate of 600m ^ 3 / m * i * n and leaves at 95 kPa and 60 degrees * C . Determine the mass flow rate of the refrigerant
Refrigerant-134a is to be cooled by water in a condenser. The refrigerant enters the condenser with a mass flow rate of 6 kg/min at 1 MPa and 70°C and leaves at 35°C. The cooling water enters at 300 kPa and 15°C and leaves at 25°C. Neglecting any pressure drops, determine the heat transfer rate from the refrigerant to water.
A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500°C and exhausts from the turbine as wet steam with a quality of 97% at 20 kPa. Determine the turbine's efficiency and estimated lost work.
Determine the isentropic efficiency of the rotary engine and the second law efficiency of therotary engine when the Water vapor inlet a rotary engine at 500 oC temperature and 1200 kPa pressure and exits at 300 oC temperature and 200 kPa pressure.. According to this: (take close temperature of 25 0C)
Air enters the compressor of a gas turbine plant at ambient conditions of 100 kPa and 25 ⁰Cwith a low velocity and exits at 1 MPa and 347 ⁰C with a velocity of 90 m/s. The compressionprocess is adiabatic, and the power input is 270. Determine the mass flowrateof the air through the compressor.
Consider the turbocharger of an internal combustion engine. The exhaust gases enter the turbine at 450°C at a rate of 0.02 kg/s and leave at 400°C. Air enters the compressor at 70°C and 95 kPa at a rate of 0.018 kg/s and leaves at 135 kPa. The mechanical efficiency between the turbine and the compressor is 95 percent (5 percent of turbine work is lost during its transmission to the compressor). Using air properties for the exhaust gases, determine the air temperature at the compressor exit.