Plz solve this now in 20 min and get a thumb up plz plz Consider the tin (Sn)- bismuth (Bi) equilibrium diagram reproduced below. An alloycontaining 10wt% Bi is held at a temperature of 200°C31300271Liquid250232200B+ Liquida + Liquid15018.4138.5C100a+BSn10 20 30405060708090BiWeight Bismuth(a) Name the phases present in equilibrium at this temperature.5. aneadue

A question based on phase diagram, which is to be accomplished.

Consider the tin (Sn)-bismuth (Bi) equilibrium diagram reproduced below. An alloy containing 10wt% Bi is held at a temperature of 200°C 300 271 250 Liquid 232 200 B +Liquid a+ Liquid 150 18.4 13SC 98 100 a+B 50 10 20 30 40 50 60 Weight Bismuth 70 80 90 Bi (a) Name the phases present in equilibrium at this temperature Temperature, C

Consider the tin (Sn)-bismuth (Bi) equilibrium diagram reproduced below. An alloy containing 10wt% Bi is held at a temperature of 200°C 300 271 250 Liquid 232 200 B +Liquid a+ Liquid 150 18.4 13SC 98 100 a+B 50 10 20 30 40 50 60 Weight Bismuth 70 80 90 Bi (a) Name the phases present in equilibrium at this temperature Temperature, C

Physical Chemistry

2nd Edition

ISBN:9781133958437

Author:Ball, David W. (david Warren), BAER, Tomas

Publisher:Ball, David W. (david Warren), BAER, Tomas

Chapter6: Equilibria In Single-component Systems

Section: Chapter Questions

Problem 6.50E

See similar textbooks

Similar questions

The table below shows temperature/composition data collected for a mixture of methylbenzene (M) and octane (O) at 1 atm. Recall that x stands for the mole fraction in the liquid and y stands for the mole fraction in the vapor in equilibrium. The boiling points for methylbenzene (M) and octane (O) are 110.60C and 125.60C, respectively. Construct the phase diagram with Temperature vs. xM. What is the composition of the vapor in equilibrium with the liquid of composition (a) xM = 0.250 and (b) xO = 0.250. T (0C) 110.9 112.0 114.0 115.8 117.3 119.0 121.1 123.0 xM 0.908 0.795 0.615 0.527 0.408 0.300 0.203 0.097 yM 0.923 0.836 0.698 0.624 0.527 0.410 0.297 0.164
An aerospace manufacturer is building a prototype experi-mental aircraft that cannot be detected by radar. Boron nitride ischosen for incorporation into the body parts, and the boricacid/ammonia method is used to prepare the ceramic material.Given 85.5% and 86.8% yields for the two reaction steps, howmuch boron nitride can be prepared from 1.00 metric ton of boric acid and 12.5 m³ of ammonia at 275 K and 3.07X10³ kPa?Assume that ammonia does not behave ideally under these con-ditions and is recycled completely in the reaction process.
give 5 examples of a 1 phase diagram and show its phase rule
A cylinder containing ethanol is submitted to a certain pressure. At a temperature of 273 K, when the applied pressure is 1.0 atm, the vapor pressure of the ethanol is 1.25 kPa. Considering that the molar volume of ethanol at 273 K is 1.22 x 10-2 dm3/mol, calculate the vapor pressure of ethanol when the pressure on the liquid reaches 4.00 MPa.
Sketch the cooling curves for the isopleths a and b in Fig. 5.4.
4 The Liquid-Vapor Equilibrium line in a one component system should always have a positive slope on a Pressure-Temperature diagram. Explain why? Draw a neat phase diagram of a one component system that can exist in two allotropic forms.
Pressure was exerted with a piston on molten naphthalene at 95 °C. The vaporpressure of naphthalene when the applied pressure is 1.0 bar is 2.0 kPa. What is thevapor pressure when the pressure on the liquid is 15 MPa? The mass density ofnaphthalene at this temperature is 1.16 g cm-1.
is the phase diagram of sulphur. At 95.4˚C, the densities of rhombic andmonoclinic sulphur are 2.07 g cm-3and 1.96 g cm-3, whilst the enthalpy change for thephase transition from rhombic to monoclinic sulphur is 0.3 kJ mol-1. i) How many triple points are there?ii) What is the most stable form of sulphur under normal conditions?iii) Describe what happens when sulphur at 1 atm is heated from 80˚C to 200˚C.iv) Determine the volume change ΔV for the transformation from rhombic tomonoclinic sulphur.v) Estimate the pressure at which rhombic and monoclinic sulphur coexist inequilibrium at a temperature of 373 K.
The solid–liquid equilibrium line in the phase diagram of water has a negative slope, equal to −0.0076 °C bar−1. Calculate the freezing point of water beneath a glacier that is 3 km high and has a density of 917 kg/m3.
What is the change in the boiling point of water at 1000 C per Pa change under atmospheric pressure conditions? The molar enthalpy of vaporization is 40.69 kJ mol-1, the molar volume of liquid water is 0.019 x 10-3 m3 mol-1, and the molar volume of steam is 30.199 x 10-3m3 mol-1, all at 100.000 C and 1.01325 bar. (Hint: change in temperature per change in pressure, dT/dP).
Some nonelectrolyte solute (molar mass = 142 g/mol) was dissolved in 150. mL of a solvent (density = 0.879 g/cm3). The elevated boiling point of the solution was 355.4 K. What mass of solute was dissolved in the solvent? For the solvent, the enthalpy of vaporization is 33.90 kJ/mol, the entropy of vaporization is 95.95 J/K mol, and the boiling-point elevation constant is 2.5 K kg/mol.
a) The following temperature composition data were obtained for a mixture of two liquids A and B at one atmosphere, where x is the mole fraction of A in the liquid and y is the mole fraction of A in the vapour, at equilibrium.t/ oC 125 130 135 140 145 150xA 0.91 0.65 0.45 0.30 0.18 0.098yA 0.99 0.91 0.77 0.61 0.45 0.25the boiling points are 124 oC for A and 155 oC for B. Plot the temperature-composition diagram for the mixture on a graph sheet. What is the composition of the vapour in the equilibrium with the liquid of composition i) xA = 0.50 and ii) xB= 0.33