Consider the truss shown in (Figure 1). Take A = 0.0015 m? and E = 200 GPa for each member, and F = 17 kN. when the deflection is downward and positive value in the case when the deflection is upward. HA ? Ay2 = Value Units Submit Request Answer Part B Figure < 1 of 1> Determine the force in member 4 of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. F 4 m m ? 94 = Value Units 3 m Submit Request Answer

Consider the truss shown in (Figure 1). Take A = 0.0015 m? and E = 200 GPa for each member, and F = 17 kN. when the deflection is downward and positive value in the case when the deflection is upward. HA ? Ay2 = Value Units Submit Request Answer Part B Figure < 1 of 1> Determine the force in member 4 of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. F 4 m m ? 94 = Value Units 3 m Submit Request Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the largest force P (kN), directed as shown in the figure that can be applied to the bracket if the allowable normal stresses on section A-B are 8 Mpa in tension and12 Mpa in compression. A119.15 B.79.44 C.18.64 d.14.31 answer:14.31
In the overhanging beam show, determine P so that the moment over each support equals the moment at the midspan. W= 3.7 kN/m. Round your answer to 2 decimal places.
A simply supported 4-m long beam is made up of 80% grade Kato. The beam is carrying a uniform load of 12 KN/m all through out its length and a concentrated load of 800 N 1 meter from the left support. The cross-sectional area of the beam is indicated below. *USE 2 DECIMAL PLACES IN EVERY VALUES 1. What is the maximum shear of the beam in KN? (use two decimal places) 2. What is the maximum moment of the beam in KN.m? (use two decimal places) 3. What is the total cross-sectional area of the beam in mm2? (use two decimal places)
Question 1) F=20 kN single load, M=23 kN.m moment and w=19 kN/m distributed load are acting on the beam whose loading condition is given in the figure . The length L is also given as L=5 m . The cross-sectional properties of the beam are; body height y g =248 mm , body thickness x g =12 mm , flange width x f = 196 mm , flange height y f = 20 mm . Point E on the section is located just below the flange-body junction. It is desired to determine the stress state in the section taken from the C level of the beam. According to this; Question1-A ) Find the normal force (N C ) at point C. ( Write your result in kN .) Question1-B ) Find the shear force (V C ) at point C. ( Write your result in kN .) Question1-C ) Find the bending moment ( MC) at point C. ( Write your result in kN.m. )
Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of the 5-kip load. Follow the sign convention. a) Determine the normal force at point E. Express your answer in kilopounds to three significant figures. b) Determine the shear force at point E. Express your answer in kilopounds to three significant figures. c) Determine the moment at point E. Express your answer in kilopound-feet to three significant figures.
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
Calculate the vertical shear stress (N / cm2) at point A in the critical section of the beam below whose load and section is given? The cross section is symmetrical with respect to the y-axis. (Point A is on the body, point B is on the x-axis and point C is on the header.) (Q = 6000 N / m, P = 60000 N, L = 3 m, b = 50 cm t = 5 cm, h = 20 cm) please fast help please
Determine the axial force in member DE in kN. Use F1 = 77 kN, F2 = 60 kN, x = 3.65 meters, y = 3.24 meters. Round off to two decimal places. Input the numerical value only.
A cantilever beam AB with a circular crosssection and length L = 750 mm supports a loadP = 800 N acting at the free end (see figure). Thebeam is made of steel with an allowable bendingstress of 120 MPa.(a) Determine the required diameter dmin (figurepart a) of the beam, considering the effect of thebeam’s own weight.(b) Repeat part (a) if the beam is hollow with wallthickness t =d /8 (figure part b); compare thecross-sectional areas of the two designs.
The steel truss shown carries a downward vertical load of 14 kN at joint B. The diagonal members of the truss have an area equivalent to 250 mm^2, and the horizontal members are 300 mm^2. With the given conditions calculate the: a) Horizontal Deflection at E in mm b) Vertical Deflection at D in mm Esteel = 200 GPa
Q9c. For the beam below, the point loads and distances are as follows: F1 = 11. 25 kN, F2 = 11.25 kN and F3 = 4.50 kN L1 = 2.25 m, L2 = 4.50 m, L3 = 4.50 m and L4 = 2.25 m Determine the bending moment at D. Give your answer in kilonewton metres (kNm) to two decimal places.
For the truss in Figure 01, it is asked: choose two bars (AB, AC, AD, BC, BE, CD or CE) and determine the normal effort due to the action of load P, applied at point B, indicating the nature of the effort (whether traction or compression). To adopt:P:1100N