Constants Part A Find the flow velocity measured by a venturi meter (Figure 1). Express your answer in terms of some or all of the variables P, A1, P2, A2, and p. ? v1 = Submit Request Answer Part B Figure 1 of 1 A venturi tube is measuring the flow of water; it has a main diameter of 2.9 cm tapering down to a throat diameter of 1.6 cm. If the pressure difference is measured to be 31 mm-Hg, what is the velocity of the water? Express your answer to two significant figures and include the appropriate units. HÀ ? v1 = Value Units A2 A1 Submit Request Answer

Constants Part A Find the flow velocity measured by a venturi meter (Figure 1). Express your answer in terms of some or all of the variables P, A1, P2, A2, and p. ? v1 = Submit Request Answer Part B Figure 1 of 1 A venturi tube is measuring the flow of water; it has a main diameter of 2.9 cm tapering down to a throat diameter of 1.6 cm. If the pressure difference is measured to be 31 mm-Hg, what is the velocity of the water? Express your answer to two significant figures and include the appropriate units. HÀ ? v1 = Value Units A2 A1 Submit Request Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
A nozzle meter, with an orifice diameter of 3 cm, is being used to determine the velocity of ethanol (SG = 0.789, μ = 0.986*10-3 Pa.s) flowing through a smooth plastic pipe of diameter 6 cm. A differential mercury manometer is attached across the nozzle, showing a height from the bottom of the manometer of 10 mm Hg on one side of the nozzle meter and 150 mm Hg on the other. (ρHg =13600 kg/m3). What is the volumetric flowrate of the oil?
A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
kindly help me with this problems INSTRUCTIONS: Solve the problems neatly and systematically. SUse free-floating decimals in all your calculations and in expressing your answers. Box your final answers. 2. Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s
Using a flexible drinking straw and a ruler, explain how you would measure the water flow velocity in a river.
Three pipes connected in series with lengths L1 = L2 = L3 = 150 m and diameters D1 =75 mm, D2 = 50 mm, D3 = 25 mm. The discharge at the 25mm pipe = 200 lps, kinematic viscosity = 1.12 x 10-6 m2/s and ε = 0.35 mm. Using Colebrook and Darcy-Weisbach Formula, determine the following:a. relative roughness of the 25mm pipeb. roughness coefficient of 75mm pipec. head loss of 50 mm pipe
An oil of specific gravity 0.9 is flowing through a venturimeter with inlet diameter of 300 mm and throat diameter of 205 mm. A differential manometer connected to the inlet and throat of the venturimeter gives a difference in the reading of 27 cm of mercury. Take coefficient of discharge of the venturimeter (Cd) as 0.96. Find the following Inlet area of the Venturimeter (in m2) Answer for part 1 Throat area of the Venturimer (in m2) Answer for part 2 Differential pressure head 'h', (in m of oil) Answer for part 3 Discharge of oil through Venturimeter (in m3/s) Answer for part 4 Discharge of oil through Venturimeter (in Litre/s)
The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
Fundamental of fluid flow: A venturi meter with a throat diameter of 6 cm is fitted in a horizontal pipeline of 12 cm diameter with oil of specific gravity 0.88 flowing from left to the right. The difference in level in the two limbs of a mercury manometer connected to the tapping points read 12 cm and the connecting pipes are filled with the same oil. (a) If two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet. Determine the difference between the 2 gage pressure readings in kPa. (b) Determine the flow in m^3/s neglecting head losses.
The velocity of a fluid flowing in a pipe is to be measured by two different Pitot-type mercury manometers shown in Fig. Would you expect both manometers to predict the same velocity for flowing water? If not, which would be more accurate? Explain. What would your response be if air were flowing in the pipe instead of water
An orifice having an area of 0.0003 m² is located on the vertical side of a tank. The tank has a constant cross sectional area of 0.40 m². It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Using c=0.60, which of the following most nearly gives the head in meter after 240 seconds from an initial head of 1.20m?