Construct the circuit of the following function using 3:8 decoder and 2:4 decoder only: F(A,B,C,D) =(A+B')(C'+D°) NB: You must use both the decoders in a single circuit. Your circuit should be cost efficient, meaning you have to use the lowest number of components possible. You should use external gates for connecting inputs/outputs if required.

Construct the circuit of the following function using 3:8 decoder and 2:4 decoder only: F(A,B,C,D) =(A+B')(C'+D°) NB: You must use both the decoders in a single circuit. Your circuit should be cost efficient, meaning you have to use the lowest number of components possible. You should use external gates for connecting inputs/outputs if required.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Use VHDL to implement a 16-to-1 Multiplexer. The inputs are w0, w1, w2, w3, w4, w5, w6, w7, w8, w9, w10, and w11. The last four inputs are not attached to an input signal. How many select bits need the circuit?
implement the following boolean function using a 4x1 multiplexer. connect inputs A,B,C to the selection lines. F(A,B,C,D) = 0,1,2,4,8,9,12,13
Implement the following Boolean function by using 2x1 multiplexers only.F(A,B,C,D) = ∑ (1,3,4,8,10,11,13,14)
Write a function to generate an output voltage of 0.5V on the CCP2 pin. Consider a resolution of 12 bits, a fosc of 16MHz, Vcc of 3.3V and a Vss of 0V. It is necessary to include the proper pin configuration.
Encode the function f(w, x, y, z) = Σm(0, 1, 3, 4, 7, 6, 9, 11, 10, 13, 14). You must label your product terms and use the left-most and top-most input/output lines for any required feedback forcredit
Consider a special purpose decoder that is called BCD to seven-segment decoder. The decoder takes a 4-bit Binary Coded Decimal (BCD) number X3 X2 X4 X0 (0-9) and produces 7 outputs a, b, c, d, e, f, and g The specification of this circuit is as follows: ⚫ The 7 outputs of the decoder are connected to LED segments as shown in the figure below. The LEDs are active low, ie, the LED emits light when it is connected to logic 0. • The decoder output is determined in a way so that the LED segments display the decimal representation of the input. For example, if the input X3 X2 X1 X0 is 0001 respectively (which is equivalent to decimal 1), the outputs a, b, c, d, e, f, and gare 1001111 showing the letter 1 on the display (remember the LEDs are active low). Decoder W- 4x7 e U Answer the following questions: a. Fill in the truth table of that decoder. Choose a good value for the output when the input is greater than decimal 9. b. Derive the simplified Boolean expressions for the outputs a, b, c,…
Using Verilog continuous assignments or VHDL signal assignments, write a description of the circuit specified by the following Boolean functions: Out_1=(A+B′)C′(C+D)Out_2=(C′D+BCD+CD′)(A′+B)Out_2= (AB+C)D+B′CWrite a testbench and simulate the circuit’s behavior.
We want to design a circuit that counts the number of 1s present on 3 binary inputs a, b, c and outputs that number in binary using 2 outputs y and z. For example an input of a=1, b=1, c=0 has two ones, so the output would be 210 = 102 i.e., y=1, z=0. a) Express y and z as sum of min‐terms of variables a, b and cb) Simplify the expressions for y and z using K maps.c) Draw the logical circuits for y and z using gates.
Build the following function using only 8x1 Mux: F(a,b,c,d,e) = ∑ (0, 4, 8, 16, 17, 20, 22, 24, 25, 31) [NB: Must show MSB & LSB] [NB: The circuit should be cost efficient. Meaning, try to use lowest number of ICs possible for an optimum design]
Implement the following Boolean functions with suitable PLD use : 1- PROM 2- PLA 3- PAL F1 ( A , B , C , D ) = { m ( 5,6,7,9,10,11,13,15 ) F2 ( A , B , C , D ) = { m ( 6,9,10,11,13,15 ) F3 ( A , B , C , D ) = { m ( 6,7,9,10,11,13,15 ) F4 ( A , B , C , D ) = m ( 0,1,3 , 15 )
Matlab generator++. Full code and plotting neweful. Task(5): Run the following code and note down the output. Also use real, imag and abs functions to plot real part, imaginary part and magnitude.>> n = [0:5]; x = exp ((2+3j)*n) Task(7): Write a program in Matlab to generate 1.5 s of a 50 Hz Saw tooth Waveform withsample rate fs = 10000 and plot 0.2 s of the generated waveform Task(1): Write a MATLAB code to sum unit step and unit ramp function . subject is signal and system please solve me all three.
Draw a 4-input adder for single-bit values: that is, a set of logic gates with 4 input wires each representing a number between 0 and 1 and a multi-bit output z, composed of wires z0 through z... (where z0 is the low-order bit, z1 the next, etc., up to the number of wires needed for this task). The gates should ensure that z = the sum of all four inputs.