Cords AB, AC, and AD can sustain a maximumtension of 53 N before they fail. (Figure 1)PartDeterExpreWmSubProvide FeediFigure1 of 160303045° 397fbda1cb26b39fcfa2d032f29b1#10001Part ADetermine the greatest weight of the flowerpot the cords can support.Express your answer to three significant figures and include the appropriate units.HA?Wmax =90.477SubmitPrevious Answers Request AnswerX Incorrect; Try AgainProvide Feedback

The maximum tension to test the cable is given as, T=53 N

Answered: Cords AB, AC, and AD can sustain a…

Engineering

Mechanical Engineering

Cords AB, AC, and AD can sustain a maximum tension of 53 N before they fail. (Figure 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 5 hp motor with a speed of 900 rpm is used to drive an industrial fan with a velocity of 5.72m/s. The center distance between the sprockets is 1.5 times the diameter of driven sprocket andis equal to 630 mm. Determine the length of chain in pitches. Use RC 40 chain and service factorof 1.3.
Determine the size of the clutch plate suitable for an Ambassador car employing asingle plate type friction clutch and developing 37.5 kW at 4282 rpm. The insidediameter of the clutch plate is 0.6 times its outside diameter and it is to be ensured thateven after a loss of 30% of the engine torque due to wear of the clutch facing, the clutchdoesn’t slip. The intensity of the pressure on the facing is not to exceed 70 kPa. Assumeµ = 0.3.
The drive is by V-belts from an electric motor running at 1500 r.p.m. A compressor, requiring 75000W is to run at about 500 r.p.m. The diameter of the pulley on the compressor shaft must not be greater than 1.2 meter while the centre distance between the pulleys is limited to 1.85 meter. The belt speed should not exceed 1500 m/min. Determine the number of V-belts required to transmit the power if each belt has a cross-sectional area of 3 cm2, density 1100 kg/m3 and an allowable tensile stress of 3 MPa. The groove angle of the pulley is 50°. The coefficient of friction between the belt and the pulley is 0.3. Calculate also the length required of each belt.
The turning moment diagram for a multi cylinder engine has been drawn toa scale of 1 mm = 4500 N -m vertically and 1 mm = 2. 4 ͦ horizontally. Theintercepted areas between output torque curve and mean resistance lineabove and below the mean taken in order from one end are 342, 23, 245,303, 115, 232, 227, 164 ??2, when the engine is running at 150 rpm. Ifthe mass of the flywheel is 1000 kg and the total fluctuation of speed doesnot exceed 3% of the mean speed, find the minimum value of the radius ofgyration.
The connection between an electric motor and a construction machine shaft is provided by means of a rigid coupling with flanges, through which the moment is transferred via the coupling flanges.The power of the electric motor is 35kw and the speed is 870rpm. The coupling flanges are connected with three bolts of quality 5.6 with a placement diameter of 40 mm.The surface pressure safety stress for bolts is 16 MPa. The contact length of the bolt with the coupling flange is 12 mm. The coefficient of friction on the flange surfaces is 0.14; the operating factor for the coupling is 0.8. The working conditions of the contact element, the material properties are very well known; since force and stress analyses can be performed with high accuracy,; question) Determine the bolt that should be used in the clutch from the table.
der engine has been drawn 0 2 moment diagram for a multicylin ~ 2.4° horizontallv. e = 4500 N-m vertically and 1 mm 'mxemapwd areas between output torque curve and the mean resistance line taken in order from one end are 342. 23, 245. 303. 115. 232. 227. 164 mm2. when the engine is running at 150 r.p.-m- If the mass of the flywheel is 1000 kg and the tota! fluctuation of speed does not exceed 3% of the mean speed. find the minimum value of the radius of gyration 16.4/ The turning
A flat belt, of density 1000 kg/m3 has a maximum permissible stress of 2·5 MN/m². Thebelt is 200 mm wide and 12 mm thick.(a) Determine the maximum power that can be transmitted if the ratio of tight-side toslack-side tension is 2. The diameter of the driving pulley is 900 mm and the required speed of the output shaft is955 rev/min(b) Taking the belt thickness into account, determine the required diameter of theoutput pulley. (c) What would the required diameter be, assuming a total slip of 4%? (d) If the mass of the belt was neglected, explain the effect (with reasons) this wouldhave on the maximum power calculated in (a)
An ideal spring has a spring constant k = 24.3 N/m. What is the amount of work that must be done to stretch the spring 0.800 m from its relaxed length? ________ J
In a pin-on-disk wear test, a bronze pin of radius 10mm is placed with its flat face resting on asteel plate under a normal load of 100 N and at a distance of 200 mm from the center of thesteel plate which rotates about its axis at 5Hz for 20h. At the end of the test, the specimens areseparated and weighed and it is found that the mass losses of the bronze and steel are 250mgand 10mg respectively. Calculate the wear coefficients for bronze and steel if hardness anddensity of steel and bronze are 2.4 GPa, 0.8 GPa, 7.8Mg/m3and 8.4Mg/m3respectively.
A solid steel shaft transmits 50 KW of power at the frequency of (50/ π) Hz. The initial torque needed in the shaft is A) 812 N-m B) 678 N-m C) 541 N-m D) 500 N-m
A structural membrane contains surface flaws of initial depth of 0.015 inchesDetermine the life of the membrane in cycles if it is repeatedly loaded from 0 to 60 ksi. Assume K1=95 ksi-in¹/2, n=3 and C=4x10-10 (Ksi²cycle)^-1
The power transmitted between two shafts 3.5 metres apart by a cross belt drive round the two pulleys600 mm and 300 mm in diameters, is 6 kW. The speed of the larger pulley (driver) is 220 r.p.m. Thepermissible load on the belt is 25 N/mm width of the belt which is 5 mm thick. The coefficient offriction between the smaller pulley surface and the belt is 0.35. Determine : 1. necessary length of thebelt ; 2. width of the belt, and 3. necessary initial tension in the belt.[Ans. 8.472 m ; 53 mm ; 888 N]