Describe how you designed a vertically coded control unit.

Q: Page 429. Sample Problem 6.2.Solve the problem completely;but this time,placethe three applied…

A: The forces 2.5kpis, 1 kip, 2.5kips are replaced by 3kips, 2kips, 1 kip respectively. For timber…

Q: A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor…

A: Here, Motor power, P=12 hp Speed, N=1150 rpm Distance, d=12 in Wheel size, r=13 in Linear speed,…

Q: In a typical fuselage or wing section, the stringers and spars would carry most of the mainly…

A: The stringers and spars  are the axial member in the fuselage and used to resists bending .   As…

Q: = 20 rad/ When the gear makes 29 revolutions, it reaches an angular velocity of w s, starting from…

A:

Q: 20. A steel shaft is transmitting 50 hp at 1,200 rpm. The nature of the load and type of service of…

A: Given data  Power= 50hp Speed = 1200rpm  Stress = 4000(psi)  Find the torsional deflection at the…

Q: Please provide handwritten answer

A:

Q: The object (W 1000 lb) is moving between positions G and H back and forth repeatedly. The bar AD is…

A: W=1000 lbSy=80 ksi=80×103 psiS'n=20 ksi=20×103 ksiN=2

Q: Consider the tripod in (Figure 1). Figure 15m 2m 2m 2.5m < 1 of 1

A: Solution: The coordinate of the points are : A=(0,2,0)B=(3.5,2.5,0)D=(2.5,2,4) The direction cosine…

Q: Problem 2: A composite shaft is composed of a solid section AB and a tubular section BC, both of…

A:

Q: The three principal stresses at a given point are σ1 =60 MPa, σ2 =−100 MPa, σ3 =−10 MPa. If the…

A: Given: The principal stresses;σ1=60 MPaσ2=-100 MPaσ3=-10 MPaYield stress, Sy=250 MPaFind:i The…

Q: 3. a) Develop the shear force and bending moment equations for each section. b) Sketch the shear…

A: a) Develop the shear force and bending moment equations for each section. b) Sketch the shear force…

Q: Problem 1: Three vertical posts AD, BE, and CF are held between two horizontal rigid plates. Posts…

A:

Q: 15. A shaft supported on bearing 8 inches apart transmits 250 hp at 200 rpm. The maximum bending…

A: Given data  Power = 250hp  Speed= 200 rpm  Maximum bending moment= 24000(lb.in)  The allowable shear…

Q: Part A Determine the maximum shear stress in the T-beam at the section where the internal shear is…

A: w₁ = 28 kN/m  w₂ = 42 kN/m

Q: The slotted arm OA rotates about a horizontal axis through point O. The 0.30-kg slider P moves with…

A:

Q: What is the moment developed at the fixed support (A)

A: Given data is

Q: 7-104 An air conditioner with refrigerant-134a as the working fluid is used to keep a room at 23°C…

A:

Q: yl у 6 4 10 5 X

A: Given data:- U-Channel To find:-  y- for the cross-section

Q: Problem 2. Two projectiles are fired at the same instant, projectile A is launched horizontally with…

A: VA=12 m/sy=6mx=6mVBo=?

Q: = Gear B has an angular acceleration of a b 0.15t² rad/s², where t is in seconds, and an initial…

A: Angular acceleration of gear B→αB=0.15t2  ...............equation1→dωBdt=0.15t2→ωBf-ωBi=0.15t33…

Q: As shown in the figure below, Refrigerant 134a is contained in a piston-cylinder assembly, initially…

A: Given: The weight of the piston is W= 471.1 N. The diameter of the piston is d=0.02 m. The final…

Q: How much heat and moisture must be added to 4 cubic meter per minute of air at 13 C dry bulb and 31%…

A: The volumetric flow rate of air, V = 4 m3/min The dry bulb temperature of air, Tdb,1 = 13 C The…

Q: 8. what is the magnitude of maximum stress that exists at the tip of an internal crack having radius…

A: Given:Radius of curvature of the crack, ρt=1.9*10-4 mmCrack length, a=3.8*10-2 mmThe nominal applied…

Q: A tensile force of 100 kN is applied on a 0.02-m diameter and 2-m long rod. After applying the load,…

A: Tensile force (P)=100 kN Original diameter (do)=0.02 m Original length (Lo)=2 m Final diameter…

Q: Question 1: The 8-kg ball is connected with a spring as shown. Initially the spring is compressed by…

A:

Q: A fan delivers 400 m3 /min of air at 1 atm and 21 C when rotating at 600 rpm, with a head of 8 cm…

A: The volumetric flow rate of the air, V = 400 m3/min The pressure of the air, P = 1 atm The…

Q: Find the. Force

A: Given  The magnitude of Force F1= 1000 N                                        F2=880 N

Q: 6 The plate shown moves in the xy plane. Knowing that (vÃ)x= 12 in./ (VB)X = -4 in./s, and (vc)y= =…

A: Given data is

Q: The ducted fan unit shown in the figure has mass m = 100 kg and is supported in the vertical…

A: mass of the  fan unit mu=100 kgAt inlet 1ρ1=1.2 kg/m3V1=5 m/sD1=1mAt exit 2m˙2=12m˙1V2=15m/sθ2=55oAt…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: Determine all forces acting on member ACE and BCD of the frame shown below. The diameter of the…

A: The mass of the body is m=100 kg. The diameter of the pulley at E is d=120 mm.

Q: The 3-dimensional state of strain at a material point in x, y, z Q3 coordinates is given by: [8] xx…

A:

Q: Blocks A and B have masses of 200 kg and 100 kg, respectively. They rest on a 30° inclined plane and…

A: Here, given that, Mass of block A, mA = 200 Kg Mass of block B, mB = 100 Kg We have to find…

Q: Q1 If the atmosphere is 50 km thick, and the atmospheric pressure at sea level is approximately 101…

A: Atmosphere thickness = 50 km = 50000 m. Atmospheric pressure at sea level is approximately = P= 101…

Q: A pipe of 1.0 m diameter carries water to a municipality. Water is to be distributed to two…

A:

Q: A 2Hp motor rotates at 1500 rpm. If the allowable torsional stress is not to exceed 40 MPa, what is…

A: Power of motor = P = 2HP = 1.491 KW N = 1500 RPM τallowable = 40Mpa

Q: Water flows into a tank and out through another pipe, as shown in the figure below. The water in the…

A: Given:Surface area, Asurf=5.8 m2Inclination angle of door, θ=40oLength of the door, L=1.1 mWidth of…

Q: At a given instant A has the motion shown in (Eigure 1). Figure 3 ft 1.5 ft PA-3 ft/s a-681/8² 1 of…

A: The disk does not slipso that,a0=αr=6×0.5=3m/s2By using relative acc. equation-ac=a0+α×r-ω2r…

Q: Using the top view, right-side view, and front view. Draw the isometric view.

A: Given: Draw the isometric view.

Q: Calculate the following reaction forces for the A-frame shown below. Take the lengths a, b and c as…

A:

Q: Q1: a) Find the vector expression for F on AD, b) Find its projection along AC. 3 m D B DA T=4.2 KN…

A: TAB = 4.2 KN

Q: Determine the shear and moment diagram with maximum shear and maximum moment.

A: We have given that, Moment at C of 150 KN-m Point D have roller joint Point B is fixed UDL of 35…

Q: 6. Determine the factor of safety needed for a 2-inch diameter shaft with an ultimate strength of…

A: Given: The diameter of shaftd=2 in The ultimate strength of shaft σu=50000 psi Torque T=40000 in-lb

Q: 1 of 1 Part A Determine the horizontal and vertical components of force at pin A of the two-member…

A:

Q: Homework 1 H.W//Draw shear force and bending moment diagrams by using Equation method for the…

A:

Q: The inclined block A is given a constant large rightward acceleration a. Determine the range of…

A:

Q: To determine the frictional stress exerted by fluid on a smooth wall, velocities v, and v2 are…

A: To determine the frictional stress exerted by fluid on a smooth wall, velocities v, and v2are…

Q: Q.5) A beam with a pin support at A and a roller support at B is subjected to distributed loads, a…

A: FBD

Q: Find the state-space equation of the following mass-spring- damper system. Assume that the bottom…

A: Solution: Given Data:   To Find: State-space model of the system.

Q: Consider a pressure transducer connected to a pipe through a connecting tube of diameter 3.5 mm and…

A: Givend=3.5mmL=50mmμ=0.001 Pa.St=7sC=25×106 mm3/bar=25×106 mm3/105Pa=250 mm3/Pa

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.