Design a compound gear train with a +120:1 ratio and diametral pitch of 5 teeth/inch. Assume ø= 20° and avoiding interference between pinion and gear; i.e., use Table 9-5a page 495. Draw a front-view using circle template or compass and a top-view using a ruler.

Design a compound gear train with a +120:1 ratio and diametral pitch of 5 teeth/inch. Assume ø= 20° and avoiding interference between pinion and gear; i.e., use Table 9-5a page 495. Draw a front-view using circle template or compass and a top-view using a ruler.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A parallel helical gear set of 19 tooth pinion is driving a 57 tooth gear. The helix angle of 20 degrees while the normal pressure angle is 14.5 degrees and the normal diametral pitch of 10 teeth/inch. If the pinion is rotating at 1800rpm and transmits 50hp, find the normal force. Please answer in detailed solution.
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise. b)Show the useful working length and the limit working length on the figure
A 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.
A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20° pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio. Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameter for the pinion and gear. If the center distance is increased by 0.125 in., what are the new values for the contact ratio and the pressure angle?
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14,5. The wheelchair has a maximum velocity of 5 m/s when it's pinion rotates at 800 rpm. Calculate : 1.1)The magnitude of the velocity of slip of gears in mesh 1.2)The angular speed of the gear wheel in rad/s 1.3)The maximum length of a path of the approach in mm 1.4)The length of a path of a recess in mm. 1.5) The addendum of the gears in mm. 1.6) The contact ratio
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
Consider a compound gear train to be designed for an exact velocity ratio of 90. The most acceptable velocity ratios per stage are ?
The parallel shafts are connected with two full depth spur gears, with a pinion module of 4 mm. The pressure angle is 25 degree. The number of teeth of the gear is 52. The angular speed ratio is desired as 2,6. Calculate the pitch line velocity (m/s) where the angular speed of the pinion is 2600 rev/min.
8.7 A pair of involute gears with 16° pressure angle and 6 mm module is in mesh. The number of teeth on pinion is 16 and its rotational speed is 240 r.p.m. When the gear ratio is just 1.75, find, in order that the interference is just avoided, (a) the addenda on pinion and gear wheel (b) the length of path of contact, and (d) the maximum velocity of sliding of teeth on either side of the pitch point. (DAV Indore, 1989) (Ans. a, 9.6 mm; a 4.2 mm; 35.41 mm; V = 95.58 cm/s) %3D
A 17-tooth pinion meshes with an 84-tooth gear. The full-depth involute gear teeth have 20°pressure angle and a diametral pitch of 32. Determine the base pitch and the contact ratio.Also,calculate the addendum, dedendum, circular pitch, tooth thickness, and the base diameterfor the pinion and gear. If the center distance is increased by 0.125 in., what are the newvaluesfor the contact ratio and the pressure angle.
The figure shows a double-reduction helical gearset. Pinion 2 is the driver, and it receives a torque of 1200 Ibf • in from its shaft in the direction shown. Pinion 2 has a normal diametral pitch of 8 teeth/in, 14 teeth, and a normal pressure angle of 20° and is cut right-handed with a helix angle of 30°. The mating gear 3 on shaft b has 36 teeth. Gear 4, which is the driver for the second pair of gears in the train, has a normal diametral pitch of 3 teeth/in, 15 teeth, and a normal pressure angle of 20° and is cut left-handed with a helix angle of 15°. Mating gear S has 45 teeth. Find the magnitude and direction of the force exerted by the bearings C and D on shaft b if bearing C can take only a radial load while bearing D is mounted to take both radial and thrust loads.
A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth are to transmit 10 hp at 1500 rpm of a 4-in pinion having a total number of 28teeth. The velocity ratio desired is about mw = 4. Find the (a) normal circular pitch, (b) normal diametral pitch, (c) axial pitch, and (d) dynamic loa