Determine the forward voltage drop across the diode whose characteristics appear in Fig. 1.19 at temperatures of -75°C, 25°C, 100°C, and 200°C and a current of 10 mA. For each temper- ature, determine the level of saturation current. Compare the extremes of each and comment on the ratio of the two.

Determine the forward voltage drop across the diode whose characteristics appear in Fig. 1.19 at temperatures of -75°C, 25°C, 100°C, and 200°C and a current of 10 mA. For each temper- ature, determine the level of saturation current. Compare the extremes of each and comment on the ratio of the two.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Use complete diode to calculate the load voltage, load current and current at resistor 6 in Fig 2(a) and Fig 2(b) with ???? = 0.75Ω.
Determine the voltage and current of the diode in a) the 1st approximation, b) the 2nd approximation with the diode as silicon, c) the 3rd approximation with an internal resistance of 2 ohms. Pls show solution, thank you.
What is the voltage across it in volt if a diode with an ideality factor of 1 has a reverse saturation current of 1x10-15 A. If 1 mA of current is flowing through it while operating at 300°K. Final answer with two decimal place.
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
1. Briefly discuss the difference between Piecewise-linear model, Simplified model, and Ideal device. 2. Discuss briefly how to test junction diode. 3. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each.
Find the value of dc and ac resistance of a Germanium junction diode if the temperature is 25 degree Celcius, Reverse Saturation Current is 20 microAmperes and applied voltage of 0.1V. a.) rDC= 75.6 ohms, rAC=11.2 ohms b.) rDC= 120.7 ohms, rAC= 28.4 ohms c.) rDC= 95.1 ohms, rAC=12.3 ohms d.) rDC= 109.2 ohms, rAC=26.3 ohms
For a specially designing on junction diode, the value of the forward current is 35 mA at a forward voltage of 3 V. If the eta of the material of the diode is 1.5, then estimate the reverse saturation current.
1. From the data in table ( 1 ) , draw a graph of a diode current ( vertical axis ) versus diode voltage . 12 . Find the forward resistance ( static & Dynamic ) for each diode . 3 . Find the reverse resistance ( static & Dynamic ) for , each diode .
Sketch vo for each network of Fig. 2.161 for the input shown. Would it be a good approximation to consider the diode to be ideal for both configurations? Why?
a) To what value R must be adjusted in the following circuit to make IZ = 70 mA. Assume VZ =20 V at 65 mA and ZZ = 23 Ω. What is the Zener voltage at 70o C, if it has a positive TC of 0.08 %/oC.? b) Using a Complete diode model, find the diode current (ID), diode voltage (VD), and output voltage (Vo) for the diode circuit shown below. Given that: Vs = 20 V, RL=3 kΩ , Barrier Potential VF = 0.3 V , and r’d = 70 Ω. If the diode was reversed and IR = 200 µA, Determine the diode reverse voltage (VR)