Determine the heat flux through the composite walls as shown in Figure. The frontal area (normal to heat flow) for the layers of Fir brick and Brick is 1 sq.m. The frontal area for Asbestos and Earth layers are equal and the summation of the frontal areas of them is 1 sq.m. as shown required to answer. OPTIONS: 1.Heat flux is around 487.3 Watt 2.Heat flux is around 742.7 Watt 3.Heat flux is around 305.4 Watt 4.None

Determine the heat flux through the composite walls as shown in Figure. The frontal area (normal to heat flow) for the layers of Fir brick and Brick is 1 sq.m. The frontal area for Asbestos and Earth layers are equal and the summation of the frontal areas of them is 1 sq.m. as shown required to answer. OPTIONS: 1.Heat flux is around 487.3 Watt 2.Heat flux is around 742.7 Watt 3.Heat flux is around 305.4 Watt 4.None

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter10: Heat Exchangers

Section: Chapter Questions

Problem 10.1DP

See similar textbooks

Similar questions

GIVEN: PL ½ x 6 A36 Steel T = ½ inches REQUIRED: Block shear strength of the gusset plate
MN = 48 SN = 79 (1&3) with thickness of 7.5mm
m = 18kg and L = 1.28 m
ANSWER ASAAAAP PLS
Qigihar House in Heilongiiang Province, China Heat Loss Problems, BSCl 2101 Climate: Avg. remperature is 3.2°C Degree Days is 5000 Inside Air Temp. is 20°C Wall Construction, Inside to Out: 15mm Gypsum Plaster, Sand Aggregate Concrete Block, rectangular core, Sand and Gravi 15mm Cement Plaster, Sand Aggregate All 4 walls measure the same, 8m wide by 7mtall. The house is heated with electricity at a cost of $0.10kWh Calculate the RSI-total for the walls using the tabular method demonstrated in class, and the temperature drop through each element for the January 2.5% temperature. Calculate the rate of heat flow through the wall again for the January 2.5% temperature. Plot the temperature profile approximately to scale through a vertical cross-section of the wall. Calculate the January heating cost for the building. Calculate the annual heating cost for the building. Now add 2" ( 50.8mm ) of extruded polystyrene, smooth skin surface, 35kgm3 rigid insulation to the inside surfaces…
Pls answer thank you! A turbine is connected to a generator by means of flange coupling that has a bolt circle diameter of 600 mm. The generator output is 80 MW, 60 hz and 95 percent efficiency. If there are 18 bolts, determine the force acting on each bolt.
Exd:Design the (T-beam) section have the properties: by =1200mm , hy = 150mm, d = 500mm, b,, = 300mm d' = 90mm(if needed), use f'. = 30Mpa., f, = 400Mpa W= 4002 (LTINS Gm The solution must be based on equations ASCE 7-10 Specifications.
The values given for a radial plain bearing are:Shaft diameter = 40 mm, bearing width = 30 mm, Pem = 6 N / mm2, Radial force = 2 KN, Ty = 45 C, oil: ISO VG 15, bearing clearance = 35 µm, dynamic viscosity for given oil and temperature = 12 m Pa. sRequired:a) What is the working cycle of the shaft?b) Find the Sommerfeld number.
this answer i need relative efficiency =62.95 only dont send wrong solution
Derive the formula of the critical radius for spherical wall.
An engine cylinder has a compression ratio (r) of 7.5, a clearance volume of 35 cm3 and a piston stroke length of 325 mm. What is the bore diameter in millimetres (mm) for the engine cylinder to the nearest mm.
A. 3.) A central station has annual factors as follows; Load Factor 58.5%; Plant Capacity factor 40.9%; Plant Use Factor 45.2%. The reserve carried over and above the peak load is 8900kW. Find the installed capacity in kW