Determine the lightest W10 section (based on flexural strength) suitable for a 6.1 m simply-supported beam supporting distributed dead load of 14.5 kN/m, which includes the weight of the beam, and a uniformly distributed live load of 43.7 kN/m. The beam is continuously braced on its compression flange and has a yield stress of 345 MPa. Use LRFD. ⒸW10x68 O W10X60 O W10X54 O W10X77 O W10X88 O W10X15

Determine the lightest W10 section (based on flexural strength) suitable for a 6.1 m simply-supported beam supporting distributed dead load of 14.5 kN/m, which includes the weight of the beam, and a uniformly distributed live load of 43.7 kN/m. The beam is continuously braced on its compression flange and has a yield stress of 345 MPa. Use LRFD. ⒸW10x68 O W10X60 O W10X54 O W10X77 O W10X88 O W10X15

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve continuously. A rectangular beam has a width of 300mm and an effective depth of 550mm spand 4.0 meters on fixed supports. It carries unfactored uniform loads of DL = 25 kN/m and LL = 80 kN/m which includes the weight of the beam. It is reinforced for flexure with five 25mm diameter bars that continue uninterrupted to the ends of the span. Using detailed analysis and NSCP 2010, design the shear reinforcement at the critical section using 10mm diameter vertical stirrups. fy = 420 MPa f'c = 28 MPa
A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 mm, determine if the 2.50 m long beam is adequate to carry a uniform load of 15 KN/m and a concentrated load of 10 KN at the cantilever end in 2 ways. Use f’c = 21 MPa, fy = 275 MPa. Neglect the weight of beam. Use n = 9.Determine if the catilever beam is adequate based on strength design 2001 NSCO specifications. The 15Kn/m load is DL while the 10KN load is LL.
Consider a beam ABCD to be designed for an ultimate uniformly distributed load of 24.9 kN/m and a two-point load of 41.251 kN as shown in figure 2. The beam is simply supported at A, B, C and fixed at D. Determine the required plastic moment and select a suitable I- section by using steel table. If the yield stress =250N/mm2.
Compute the required section modulus Z of a steel beam 5.0 m between simple supports and will carrying 11 cm thick and 100 cm concrete wall weighing 30 kN/m³. Allowable bending stress is 200 MPa and the beam itself weighs 0.5 kN/m.
A 4-m span wooden beam with rectangular section simply supports a uniform distributed loading of w=17.57 in KN/m. One support (roller) is located 1-m from the left end and the other support (hinged) is located at the right end of the span. The allowable bending stress is 9 MPa and the allowable shearing stress is 0.60 MPa. Neglect the beam weight and assume the beam to have a depth to width ratio of 1.50. What is the width of the beam so that it will not exceed the allowable bending stress?
A steel tank 2m by 1.5m by 1.2m weighs 10KN when empty and is supported by two steel beams spanning 2.0m and each weighing 10KN. Design a suitable square section for the steel beams if the tank is filled water weighing 10KN/m^3 using the plastic method. The permissible bending stress on the section is 140N/mm^2 and factor of safety is 1.5
A 4-m span wooden beam with rectangular section simply supports a uniform distributed loading of w=12.78 in KN/m. One support (roller) is located 1-m from the left end and the other support (hinged) is located at the right end of the span. The allowable bending stress is 9 MPa and the allowable shearing stress is 0.60 MPa. Neglect the beam weight and assume the beam to have a depth to width ratio of 1.50. What is the width of the beam so that it will not exceed the allowable shearing stress?
For the given frame shown, analyze using cantilever method: Which of the following gives the axial load for column BD?a. 22.5 kN c. 82.5 kNb. 62.5 kN d. 45 kN Which of the following gives the shear at column DF?a. 45 kN c. 30 kNb. 95 kN d. 50 kN Which of the following gives the moment at support B?a. 160 kN-m c. 140 kN-mb. 150 kN-m d. 120 kN-m
A 5.0m long simply supported reinforced concrete beam has awidth of 350mm and an overall depth of 470mm. The beam is reinforced with 2 –28mm dia. compression bars on top and 4 –28mm dia. tension bars at the bottom, each located 70mm from the extreme concrete fiber. Concrete strength f’c = 21MPa and steel yield strength fy = 345MPa. Determine the following, A.Depth of compression block assuming both tension and compression steel yields. B.What is the ultimate moment capacity of the beam in kN.m? C.Determine the additional concentrated live load that can be applied at midspan if the deadload including the weight of the beam is 15kN/m. Hello please answer this thanks
A rectangular beam reinforced for tension has b = 300 mm, d = 480 mm. The beam is reinforced with 7 of 25 mm bars with fc’ = 21 MPa, fy =415 MPa. If the beam is a cantilever beam 3 m long and supports a uniform dead load of 15 kN/m(including its own weight) applied along its entire length, The maximum value of the concentrated live load that can be applied at the free end is _____kN.
Answer is 260 mm..don't solve incorrect beam is supported by a roller and a hinge at its extremities. The 2 kN/m is loaded entirely on its 4 m length while 5 kN concentrated load is positioned 2 m from the left end of this beam. If the beam is 80 mm wide, determine the minimum height of the beam if the flexural stress is not to exceed 10 MPa.
a) Compute the depth of compression block and b) the ultimate moment capacity of the beam shown in Figure 2. Assume fy=28MPa and fy=414MPa