Determine the maximum stress and elongation in a helical steel spring composed of 20 turns of 20 mm diameter wire on a mean radius of 80 mm when the heavy spring is supporting a load of 2 kN. a. Identify and write down the required factor to differentiate spring that considers spring curvature. b. Set up the equations of stress and elongation that is required to solve the problem. c. Solve for the unknown variables by substituting the given in the equations of stress that has been set up previously.

Determine the maximum stress and elongation in a helical steel spring composed of 20 turns of 20 mm diameter wire on a mean radius of 80 mm when the heavy spring is supporting a load of 2 kN. a. Identify and write down the required factor to differentiate spring that considers spring curvature. b. Set up the equations of stress and elongation that is required to solve the problem. c. Solve for the unknown variables by substituting the given in the equations of stress that has been set up previously.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.4P: Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.

See similar textbooks

Similar questions

The 500 N load is acting on the helical compression spring with 20 number of turns. The helical spring is having the mean diameter of 12cm,spring wire diameter is 6mm. Find the spring inside diameter. Select one: O a. 114 mm O b. 52mm O c. 150mm O d. 20mm
The value of the spring index for a helical spring is 14. Calculate the outer diameter of the spring in mm if the mean diameter is 40 mm. choose one 51.43 36.43 42.86 2.86
(8) The smaller of two concentric spring is made of 22mm diameter steel & has an outside diameter of 100mm with 10 active coils. The outer spring is made of 32mm steel spring & has an outside diameter 250mm with 8 active coils. Before the load is applied, the outer spring is 25mm longer than the inner spring. If the load of 90kN is applied to this nest of springs, (a) find the spring rate of each spring; (b) what portion of the total load is carried by each spring? Use G = 80GPa
The helical compression spring is made of 12mm wire diameter with 132 mm mean diameter. Determine stiffness of the spring when modulus of rigidity G=80 kN/mm2,number of turn is 13 and axial load is 190N. Select one: O a. 12N/mm O b. 4.5N/mm O c. 9.5N/mm O d. 17N/mm
The value of the spring index for a helical spring is 10. Calculate the outer diameter of the spring in mm if the mean diameter is 53 mm. O 69.96 O 5.30 O 58.30 O 49.55
A helical spring is fabricated by wrapping wire 0.83 in. in diameter around a forming cylinder 6.2 in. in diameter. Compute the number of turns required to permit elongation of 4 in. without exceeding a shearing stress of 17 ksi. Use formula for light spring and G = 12 × 106 psi. Input numeric value only Round your answer to 2 decimal places.
A helical compression spring has a scale of 400 lbs/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load P of 750 lbs and for the average service Determine the standard size wire diameter Determine the number of active coils Determine the solid height Determine the stress at solid height
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures
Find the spring constant if a 20. N force stretches a spring 2.0 m.
1. A helical compression spring is made of hard-drawn spring steel wire with a wire diameter d = 0.080 in and an outer coil diameter OD = 0.880 in. The ends are plain and ground, and there are 8 total coils. Determine the force F, required to close the spring, the spring constant k, the free length of this spring corresponding to n, = 1.2, and the pitch p.
O A hollow circular shaft of inner radius 10 mm outer radius 20 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, the torsional stiffness of the shaft (in kN-m/rad) is (correct to two decimal places).
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…