A compound shaft is made by mounting a brass sleeve on a steel shaft (which is considered as parallel connection). The shaft is subjected to a torque T at point B in such a way that the torque on the sleeve is twice that on the shaft. Determine the ratio of external diameter of the sleeve to that of the shaft. What will be the torque transmitted by the compound shaft if the steel shaft diameter is 56 mm and the limiting values of the shear stresses in the brass and the steel are 50 MPa and 85 MPa respectively? Gsteel= 2.4 Gbrass. ..SN=Student Number SN=43

A compound shaft is made by mounting a brass sleeve on a steel shaft (which is considered as parallel connection). The shaft is subjected to a torque T at point B in such a way that the torque on the sleeve is twice that on the shaft. Determine the ratio of external diameter of the sleeve to that of the shaft. What will be the torque transmitted by the compound shaft if the steel shaft diameter is 56 mm and the limiting values of the shear stresses in the brass and the steel are 50 MPa and 85 MPa respectively? Gsteel= 2.4 Gbrass. ..SN=Student Number SN=43

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
A solid shaft of 150 mm diameter is used to transmit torque. Find the maximum torque transmitted by the shaft if the maximum shear stress induced to the shaft is 45 N/mm2
Calculate the maximum and minimum shear stress in a hollow circular shaft of outer diameter 20 mm and thickness 2 mm, subjected to a torque of 92.7 N-m.
A 7/8 in. diameter shaft made out of ductile material is used to transmit power frommotor. The maximum allowable shear stress, τallow = 14.5 ksi is used for this shaft, andthe shaft rotates at 200 rpm. a. Find out the polar moment of inertia of the shaft. b. Find out the maximum Torque, T is being applied to the shaft. c. What would be the power of the motor?
A solid circular shaft transmits 75 kW power at 200 rpm. Calculatethe diameter of the shaft and the maximum shear stress acting on it,if the twist in the shaft is not exceeding 1 º in 2 m length of the shaft.Take modulus of rigidity as 102 GPa.
A steel shaft with a diameter 1.85 inches and length 4.25 feet transmits 75 HP from an electric motor to a compressor. The allowable shear stress is 7500 psi and the allowable angle of twist is 2.1 Degress. G= 12x10^6Deterrmine the following: (No Scientific Notation answers) a. Determine the polar moment of inertia (in in^4) of the steel shaft: b. Determine the required torque (in lb-in) as limited by stress: c. Determine the required torque (in lb-in) as limited by the angle of twist: d. Determine the minimum allowable speed of rotation (in rpm):
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (3).
The compound shaft, consisting of steel and aluminium segments, carries the two torques shown in the figure. Determine the maximum permissible value of T subject to the following design conditions: F.S. = 1.5, Tult steel = 95 MPa, Tult aluminium = 70 MPa, and o < 6° (9 is the angle of rotation of the free end). Use G = 83 GPa for steel and G = 28 GPa for aluminium
In the case of circular shaft subjected to pure torsion nonzero are: (a)Nx (b)Nx and Vy (C)Mz and Vy (D)Nx and My (E)My andVz (F)Mx
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]