Link BD consists of a single bar 1 in. wide and in. thick. Each pin has a -in. diameter and P= 8 kips. .6 in. 12 in 30 Determine the maximum value of the average normal stress in link BD if 0 = 0. The maximum magnitude of the average normal stress is ksi. This stress is in (Click to select) Y Determine the maximum value of the average normal stress in link BD if 0 = 90°. The maximum magnitude of the average normal stress is ksi. This stress is in (Click to select) v

Link BD consists of a single bar 1 in. wide and in. thick. Each pin has a -in. diameter and P= 8 kips. .6 in. 12 in 30 Determine the maximum value of the average normal stress in link BD if 0 = 0. The maximum magnitude of the average normal stress is ksi. This stress is in (Click to select) Y Determine the maximum value of the average normal stress in link BD if 0 = 90°. The maximum magnitude of the average normal stress is ksi. This stress is in (Click to select) v

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.14P: Repeat the previous problem using ? = 50° and stresses on the rotated element: sy1= 70 MPa, ??y1=-82...

See similar textbooks

Similar questions

a) The normal stress in bar BD is most nearly b) The shear stress in the pin at D is most nearly c) The shear stress in the pin at C is most nearly
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
A rod is hanging vertically, supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the tensile stress is 140MPa.
41.) A cylindrical steel pressure vessel 400 mm in diameter with a wallthickness of 20 mm, is subjected to an internal pressure of 7.875 MPa. Towhat value may the internal pressure be increased if the stress in the steelis limited to 100 MPa?
For P =100 kN, determine the minimum plate thickness t required if the allowable stress is 125 MP
Determine the required diameter (in inches) of rod AC if the allowable normal stress is 24.95 ksi and P = 12.61 kips.
The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares, each with a cross-sectional area of 340 mm2. bar (1) has a length L1 = 810 mm and bar (2) has a lenght L2 = 1080 mm. Assume dimensions of a = 480mm, b = 38mm, and c = 600mm. If the allowable normal stress in bars (1) and (2) must be limmited to 165 MPa each, determine: a) the maximum load P that may be applied at D to the rigid bar. b) The deflection at D for the load determined in part (a).
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. A 2 kip/ft distributed load is applied on member AB, which is supported by a pin at A and bar BC. The connections at points A and B are shown in detail. All pins have a diameter of 0.5 in while all members have cross-sectional dimensions of 1.5 x 1 in. Determine the following:a. maximum normal stress in member BC (ksi)b. normal and shear stress in a horizontal section across member BC apart from the pin (ksi)c. shear stress in pins A and B (ksi)d. maximum bearing stress on member AB (ksi)
The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram. Determine the normal stress (in MPa) at point A on the cross section of the drill bit at section a−a.
The turnbuckles in the diagram shown are tightened until the compression block DB exerts a force of 12,365lb on the beam at B. Member DB is a hollow shaft with an inner diameter of 1.0 inch and outer diameter of 2 inches. Rods AD and CD each have cross-sectional areas of 1.1 square inches. Pin C has a diameter of 0.78 inch. Determine the following: a.The axial stress, in psi, in BD. b.The axial stress, in psi, in CD.c.The shearing stress, in psi, in pin C.
In the figure shown if the applied force F= 24KN. Compute the stress, in MPa, in member BD.
Q-1 ) A thin cylinder of inner radius 150 mm and thickness 9 mm is subjected to an internal pressure of 9 MPa. The average circumferential (hoop) stress in MPa is equal to ?