Determine the moment of inertia of the shaded area with respect to the reference axis AB as shown in the below figure. Page 1 of 4 25 mm 25 mm 54 mm A B 25 mm 25 mm

Q: The object having a specific gravity of 3.8 is floating in mercury of specific gravity of 13.6. If t...

A: Given data specific gravity for body=3.8 specific gravity for mercury=13.6 total volume=1 cu.m  

Q: Which of the following best describes a plastic hinge? Section where extreme fibers have yielded O M...

A: Answer- MY < M > MP Explanation - Plastic hinge can be defined as yielded zone due to flexure ...

Q: A 4-meter clay layer (e = 0.92, Gs = 2.89, Cc = 0.315) is overlain with 4-meter-thick sand layer (e ...

A: For the given details,

Q: Identify at least 2 concrete manifestation of the role that science and Technology play in nation bu...

A:  science and technology helping in building the nation in various ways 1)improving the poverty 2)imp...

Q: The steel beam has the cross section shown. The beam length is L = 30 ft, and the cross-sectional di...

A:

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 1...

A: To determine the total deformation of the copper rof.   Given, Modulus of elasticity of steel (Est) ...

Q: The intersection angle of a simple is 32 degrees 4 minutes 50 seconds and its radius of the curve is...

A: Long chord is one of the elements of simple curve.

Q: A prestressed concrete pile, 409 mm in diameter, is to be driven in a clayey soil. The pile has a de...

A: Hello dear this is the solution of your problem The answer is found to be Length of the pile in the ...

Q: b.) If the beam is triangular and the top fiber is its base, derive its bending and shearing stress ...

A: Given that the beam is triangular,

Q: An engineer calculated the PW values for four alternatives to develop a remotely controlled vibratio...

A:

Q: The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wi...

A: To determine the tension in wire BD.   Given, Diameter of the steel wires (d) = 1 cm = 10 mm [1 cm =...

Q: The cable is supported at points A and B 210m horizontally apart, with B 30m higher than A. The cabl...

A:

Q: multi story structure is to be constructed using concrete that has a unit weight of 150 pcf. The pro...

A:

Q: sin (t – 1) lim t 1 t2 + 2t- 3

A: To determine the given limit.   Given: limt→1 sint-1t2+2t-3   On substituting the value of variable ...

Q: A tank in the shape of sphere is filled with fluid and then pressurized. The diameter of the tank is...

A: We will apply formula of hoop stress.

Q: 3. A hollow bronze shaft of 75mm outer diameter and 50mm inner diameter is slipped over a solid stee...

A:

Q: A circular footing is 3.66 meters in diameter. The bottom of the footing is 2.59 m. below the ground...

A:

Q: Calculate the slope (%) of the watershed  to TWO decimal places given the following information: Hi...

A:

Q: Q3- A raft foundation (12 * 8) m carrying a net pressure of 183 kN/m² is located at a depth of 3.8 m...

A: Given:- The dimension of the raft foundation = 12 m × 8 m The net pressure on the foundation = 185 k...

Q: From the figure below, it is shown that the gate is 1.0 m wide and is hinge at the bottom of the gat...

A:

Q: The deflection angles from PC to two intermediate points A and B on a simple curve are 3° and 9.3°, ...

A:

Q: What will be the efficient minimum spacing 'S' between the channels of laced column formed by 2 ISMC...

A:

Q: In a triaxial test for a cohesive soil sample, when the principal stresses are 491.33 kPa and 58.57 ...

A:

Q: Draw the shear diagram, moment diagram, and elastic curve of the loaded structure. 90 kN B 25 kN/m 1...

A: First we will calculate reactions.

Q: ISA 100 x 75 x 10 mm (cross-sectional area = 1650 mm²) Serves as a tensile member. This angle is wel...

A: We have to determine the value of area of connected angle and area of outstand angle and area of net...

Q: describes a compact section?

A: Compact section: Answer : 3:     section capable of developing its plastic moment capacity.

Q: Design a channel section [shape purlin placed on a sloping roof truss with dead load of 0.15 kN/m (c...

A: Design of channel section purlin: Given:  Spacing of purlins = 2 m span = 4 m weight of sheets = 100...

Q: Points A and B are 100 m. apart horizontally and are of the same elevation as the foot of a building...

A: Graphical representation of problem: To determine: The distance between building and point A  = (10...

Q: 1. A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is subjec...

A: Given data B = 300mm d' = 60mm Effective depth (d) = 600mm Overall depth (D) = 600 + 60 = 660mm Area...

Q: Total number of bags needed if each bag is 50kg (110lbs) and total weight of aggregates and water ne...

A:

Q: B4

A:

Q: A 4-meter clay layer (e = 0.8, Gs = 2.74, Cc = 0.333) is overlain with 2-meter-thick sand layer (e =...

A:

Q: The members of the truss are 25mmx50mm in cross section. Determine the maximum load P that can be ap...

A:

Q: is made by welding pipe segments together. If the applied load is 1.5 k, determine the moments at th...

A: We have to determine the value of shear force and bending moment diagram according to the given data...

Q: Problem 3: Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The pl...

A: To find the increase in diameter-

Q: A small watershed has four rainfall gages located in the figure below. Total rainfall recorded at ea...

A: INTRODUCTION: the average rainfall depth is calulated by three method to analyse it. 1. Arithematic ...

Q: Pampanga sand with G; = 2.51 is mixed 26% by weight of water and compacted to produce a cylindrical ...

A:

Q: A solid round steel rod with Sy = 350 MPa is 945 mm long and 62 mm in diameter. With a safety factor...

A: To determine the allowable axial compressive load.   Given, Yield strength of the material Sy = 350 ...

Q: A steel rod with length equal to 7.5 ft, has a diameter of 0.78 inches in quarter of its length and ...

A:

Q: An orifice (area = 0.035 ft^2) is placed at the bottom of a cylindrical (diam = 5.93 ft) container. ...

A:

Q: A cube (E = 200GPA) is experiencing stress from all directions. Along thex-direction, there is a com...

A:

Q: A rectangular reinforced concrete beam with width of 300mm and effective depth of 600mm is subjected...

A:

Q: Using Isohyetal Method, find average rainfall over a catchment. The datas are: Isohyetes (cm) 12 13 ...

A:

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 1...

A: The values and diagram given in the question are as follows Initial temperature is(To)=15oC Final te...

Q: Two

A:

Q: A loaded scow has draft of 1.8 m in fresh water, when erect. The scow is 6m wide, 12 m. Long and 2.4...

A:

Q: The data shown below are the results of a liquid limit test done on a soil. Moisture Content (%) ...

A:

Q: Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 1...

A:

Q: Material A (shown below) is experiencing forces shown below at different points along its body. If t...

A: Find new length of material,L'=?

Q: velocity field is gi quation of the stre nd (2,1).

A:

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.