Pleasee solve Determine the overall voltage midrange gain, in dB, of the two-stage amplifier circuit as shown. AssumeVcc = 12 V. Also determine the output voltage across the load resistor (R.) with 5kQ. Given the followingspecifications for the transistors (Q1 and Q2) used in the circuit, Bac = 170 and Boc= 150 for bothtransistor.VccR1R3R550KR750K1.8K1.8KC3C4[100uF100uFR.V110mV / 60H2C1100µFR227KR4 h c21K ho0uFR8RS27K

We need to find out gain for given circuit .

Determine the overall voltage midrange gain, in dB, of the two-stage amplifier circuit as shown. Assume Vcc = 12 V. Also determine the output voltage across the load resistor (R.) with 5kn. Given the following specifications for the transistors (Q1 and Q2) used in the circuit, Bac = 170 and Boc = 150 for both transistor. Vcc R1 R3 R5 R7 SOK 1.8K 1.8K C3 100uF C4 100uF [ R. 02 V1 C1 10mV / 6OH2 100uF c2 IK LhoouF R2 R4 RS RS 27K 27K 1K

Determine the overall voltage midrange gain, in dB, of the two-stage amplifier circuit as shown. Assume Vcc = 12 V. Also determine the output voltage across the load resistor (R.) with 5kn. Given the following specifications for the transistors (Q1 and Q2) used in the circuit, Bac = 170 and Boc = 150 for both transistor. Vcc R1 R3 R5 R7 SOK 1.8K 1.8K C3 100uF C4 100uF [ R. 02 V1 C1 10mV / 6OH2 100uF c2 IK LhoouF R2 R4 RS RS 27K 27K 1K

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter25: Television, Telephone, And Low-voltage Signal Systems

Section25.1: Television Circuit

Problem 5R: From a cost standpoint, which system is more economical to install: a master amplifier distribution...

See similar textbooks

Similar questions

(a) What are the Q-points for the transistors in the amplifier as shown if VCC = 12 V, VEE = 12 V, REE = 270 kΩ, RC = 330 kΩ, and βF = 100? (b) What are the differential-mode gain, and differential-mode input and output resistances? (c) What are the common-mode gain, CMRR, and common-mode input resistance for a single-ended output?
In the common-emitter amplifier circuit shown in the figure, Vcc=9V, R1=27kΩ, R2=15kΩ, RE=1.2kΩ and RC=2.2kΩ. The transistor has β=100.a-) If Rsig=10kΩ and RL=2kΩ, calculate the IE value of the amplifier.b-) For small signal analysis of the transistor, find the value of Rin by deriving the π-modelc-) Calculate vo/vsig and io/ii.
(a) What are the Q-points for the transistors in the amplifier as shown if VCC = 15 V, VEE = 15 V, IEE = 400 μA, βF = 100, REE = 270 kΩ,RC =47 kΩ, VA=∞, and βF =100? (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-modeinput and output resistances? (c) Repeat part (b) for VA = 50 V.
Consider the common-source amplifier shown in Figure P11.50. The NMOS transistor has KP=50 μA/V2, L=5 μm, W=500 μm, Vto=1 V and rd=∞.a. Determine the values of IDQ, VDSQ and gm. b. Compute the voltage gain, input resistance, and output resistance, assuming that the coupling capacitors are short circuits for the ac signal. Repeat Problem P11.50 for an NMOS transistor having KP=50 μA/V2, W=600 μm, L=20 μm, Vto=2 V and rd=∞. Compare the gain with that attained in Problem P11.50.
(a) What are the Q-points for the transistors in the amplifier as shown if VDD = 12V, VSS = 12V, ISS = 1.5 mA, RSS = 33 kΩ, and RD = 15 kΩ? Assume Kn = 375 μA/V2 and VT N = 0.75 V. (b) What are the differential-mode gain, commonmode gain, CMRR, and differential-mode and common-mode input resistances?
(a) What are the Q-points for the transistors in the amplifier as shown if VDD =5V, VSS =5 V, RSS =2.4 kΩ, and RD =2.4 kΩ? Assume Kn =400 μA/V2 and VT N =0.7 V. (b) What are the differential-mode gain, common-mode gain, CMRR, and differential-mode and common-mode input resistances?
Amplifier circuit is show below has a single ac input and one ac output. Assuming 2N2222 transistor: 1- Determine the Q point, then illustrate it on the transistor I-V characteristic curves. 2- Is the transistor in the active region? Explain thoroughly. 3- Construct the T-model of the transistor with all parameters labelled and evaluated. Assume room temperature. 4- Draw a complete small signal circuit model, then find the voltage gain. Explain two characteristics of this amplifier. 5- Calculate the current gain, the input resistance, and the output resistance.
Connect the elements given below as a BJT amplifier circuit with common emitter. BJT is BC547Bterminals from left to right are named collector, base and emitter respectively. 9V battery as VCC sourcewill be used. The audio signal obtained from the microphone will be connected to the circuit as the input signal. C0 at the outlet, CI at the inlet,CE is given as a bypass capacitor.
Vs=100 mV peak-to-peak, 1 kHz sine signal, Kn=0.4mA/v^2 ,Vt=1V , λ=0.01V^-1 Make the DC analysis of the above given mosfet amplifier circuit. Simulation to tableWrite down the measured values and mathematical calculation results. (The valueswith the units.)DC Parameters ,Measured value ,Calculated ValueVGETCVGSVDVDSIDb. Draw the small signal model for the AC analysis of the circuit. Find the gm, ro, Av values.c. Show the Vs input signal and the Vo output signal of the circuit on the oscilloscope. Volt/div of channels andSpecify time/div values.
Connect the elements given below as a BJT amplifier circuit with common emitter. BJT is BC547B terminals from left to right are named collector, base and emitter respectively. 9V battery as VCC source will be used. The audio signal obtained from the microphone will be connected to the circuit as the input signal. C0 at the outlet, CI at the inlet, CE is given as a bypass capacitor.
In the circuit given in the figure, Vcc = 15 V, R1 = R2 = 10kΩ, RE = 1KΩ, RL = 0.5kΩ and transistor parameters are given as VBE = 0.7V, ßdc = ß0 = 100. a. Calculate the values of DC bias currents and voltages (IBQ, ICQ and VCEQ). b. Draw the small signal equivalent circuit of the circuit using the hybrid model of the transistor. c. Derive the input impedance expression of the circuit and calculate its value. d. Derive the AVI and AVG voltage gain expressions and calculate their values. e. Derive the current gain expression AI = I0 / Ii and calculate its value. Compare this value you have calculated with the value you will calculate using the expression Aİ = Zi AVI / RL.
The given circuit is a 2N4403 PNP common collector amplifier. Let VCC=12V, VEE=-12V, R1=52.5kΩ, R2=33kΩ, and RE=2.5kΩ. Determine IB, IC, IE, VB, VC, and VE. Start by initially assuming |VBE| =0.7V or and assuming a value of beta (β). Where to look for the value of β? (Hint: It’s in the transistor model assigned). Determine the input voltage (may extend from the supply voltage range) where the BJT goes from “cut-off to active” and where it goes from “active to saturation”. Assume VCE=0.3V (edge of saturation), RL=500Ω, and C1, C2→∞.