Discuss by your own words (You can use Arabic) without copy – paste from internet the followingclaimed arguments:|Similar answers will be badly evaluated]1- The current drawn by a 3-ph synchronous motor decreases as the leading power factor of thismotor increases when this motor is used to improve the power factor in a certain factory.2- If the magnitude of the voltage between two points in a certain transmission line is equal, then nocurrent will pass between these two points.3- The power loss in a conductor that has large diameter with respect to another conductor increasesas its length increases.4- If the capacitance between two conductors of a three phase transmission line is 8 micofarad, thenthe capacitance of each conductor of the three conductors to the neutral is 4 microfarad.

Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…

Discuss by your own words (You can use Arabic) without copy – paste from internet the following claimed arguments:|Similar answers will be badly evaluated] 1- The current drawn by a 3-ph synchronous motor decreases as the leading power factor of this motor increases when this motor is used to improve the power factor in a certain factory. If the omitudo of the uolt

Discuss by your own words (You can use Arabic) without copy – paste from internet the following claimed arguments:|Similar answers will be badly evaluated] 1- The current drawn by a 3-ph synchronous motor decreases as the leading power factor of this motor increases when this motor is used to improve the power factor in a certain factory. If the omitudo of the uolt

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.48P

See similar textbooks

Similar questions

For Problem 3.18, the motor operates at full load, at 0.8 power factor leading, and at a terminal voltage of 10.45 kV. Determine (a) the voltage at bus 1, which is the generator bus, and (b) the generator and motor internal EMFs.
A 3-phase synchronous generator is connected to an infinite bus with line-to-line voltage of 8660.3V @ 60HZ. Synchronous reactance on each line is 52. If speed of the armature is increased such that a torque angle of 20° is developed for the induced voltage, determine the total power supplied to the synchronous reactance and the infinite bus.
true or false ( answer with brief explanation ) a. The diversity in the maximum load between different loads improves the overall system load factor. b-In synchronous generators, the excitation system maintains generator voltage and controls the reactive power flow.
10.If the number of poles is constant, how to control on the generated frequency of 3 phase synchronous generators. 11.What the role of {Automatic Voltage Regulator} AVR in synchronous generators? 12.List the conditions to connecting two syn Gen's on parallel.
The figure shows the single line diagram of a single machine infinite bus system. O Infinite bus The inertia constant of the synchronous generator H = 5 MW-s / MVA. Frequency is 50 Hz. Mechanical power is 1 pu. The system is operating at the stable equilibrium point with rotor angle ō equal to 30°. A three phase short circuit fault occurs at a certain location on one of the circuits of the double circuit transmission line. During fault, electrical power in pu is Pmax sin ō. If the values of ō and do / dt at the instant of fault clearing are 45° and 3.762 radian/s respectively, then Pmax (in pu) is_
A 300-MV A 20-kV three-phase generator has a subtransient reactance of 21%. The generator supplies a number of synchronous motors over a 64-km transmission line having transformers at both ends, as shown on the one-line diagram of the following figure. The motors, all rated 13.2 kV, are represented by just two equivalent motors. The neutral of one motor M, is grounded through reactance. The neutral of the second motor M2 is not connected to ground (an unusual condition). Rated inputs to the motors are 200 MVA and 100 MVA for M1 and M2, respectively. For both motors reactance XM = 20.6%. The three-phase transformer T, is rated 350 MVA, 230/20 kV with leakage reactance of 14%. Transformer T2 is rated 220/13.2 kV, 300 MVA with leakage reactance of 10%. The series reactance of the transmission line is 0.44 Ohm/km. Draw the reactance diagram with all reactances marked in per unit. Select the generator rating as the base in the generator circuit. 13.2 kV T1 T2 200 MVA M1 JXMI 64 km G1 13.2…
6- Why it is possible to short circuit the differential compound generator and not the cumulative compound generator ?
solve both Difference between Synchronous and Asynchonous reset. Write a verilog code for synchronous reset
While preparing COPT, if identical generators are available in the system, it will follow rule a. Binomial Distribution b. Loss of Energy Probability O C. Deterministic O d. Loss of load probability
Fill in the data for a 16-ampere electric motor, single-phase, no Code letters. a. Branch-circuit protection, non-time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A b. Branch-circuit protection dual-element, time-delay fuses: Normal size _____________AMaximum size _____________A Switch size _____________ASwitch size _____________A c. Branch-circuit protection instant-trip breaker: Normal setting _____________A Maximum setting _____________A d. Branch-circuit protectioninverse time breaker: Normal rating _____________A Maximum rating _____________A e. Branch-circuit conductor size, Type THHN Ampacity _____________A f. Motor overload protection using dual-element time-delay fuses: Maximum size _____________A
8. How do you differentiate between normal neutral plane ? (DC GENERATOR QUESTION)
In synchronous motor, the rotor speed O a. is similar to the speed of the stator field O b. has no relationship to the stator filed it is only related to the rotor field O . is different from the speed of the stator field Working on de-energized lines: Select one: O a. Since the line is de-energized then its maintenance can be done in normal ways O b. Must be carried out by establishing Equipotential Zone or by using live-line tools and maintaining the minimum approach distance O. The worker should wear proper protective clothing.