Draw the memory map and show the values of the affected registers and memory locations. assuming AC initial value given below at the execution of each instruction Sn instruction 1 | Information and hint M[1E3] =125, M [235] =126, M[1E1] =127, M[1E2] =123, M[1E4] =128, M[0A4] =1E1, Initially AC=0CF1 1000000111100001 2 1101000111100010 3 0111001000111111 1110000111100011 4

Draw the memory map and show the values of the affected registers and memory locations. assuming AC initial value given below at the execution of each instruction Sn instruction 1 | Information and hint M[1E3] =125, M [235] =126, M[1E1] =127, M[1E2] =123, M[1E4] =128, M[0A4] =1E1, Initially AC=0CF1 1000000111100001 2 1101000111100010 3 0111001000111111 1110000111100011 4

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter4: Processor Technology And Architecture

Section: Chapter Questions

Problem 22VE: Two 1-bit values generate a 1 result value when a(n) _____ instruction is executed. All other input...

See similar textbooks

Similar questions

A(n) ________________ instruction always alters the instruction execution sequence. A(n) ______________ instruction alters the instruction execution sequence only if a specified Condition is true.
If a microprocessor has a cycle time of 0.5 nanoseconds, what’s the processor clock rate? If the fetch cycle is 40% of the processor cycle time, what memory access speed is required to implement load operations with zero wait states and load operations with two wait states?
Two 1-bit values generate a 1 result value when a(n) _____ instruction is executed. All other input pairs generate a 0 result value.
The time it takes to perform the fetch instruction and decode instruction steps is called the execution time. True or false?
Assume that the state of the 8088’s registers and memory just prior to the executionof each instruction in problem 15 is as follows: * in photos*What result is produced in the destination operand by executing instructions (a)through (k)? *only h through k* (h) MUL DX(i) IMUL BYTE PTR [BX+SI](j) DIV BYTE PTR [SI]+0030H(k) IDIV BYTE PTR [BX][SI]+0030H
Consider the following store instruction: SW R1, 0x000F(R0). Assume that the registers R0 and R1 are initialized with 0x00000001 and 0x53A78BC Frespectively. A section of the MIPS byte addressable data memory is shown. Give the memory word of the following memory locations after the SW operation: (a). 0x00000015. (b). 0x00000014. (c). 0x00000013. (d) 0x00000012.(e). 0x00000011. (f). 0x00000010.
Will upvote! Find the memory address of the next instruction executed by the microprocessor, when operated in the real mode, for the following CS:IP and 80286 register combinations: a. DS=2F2E & DX=9D64 b. CS=9F7A & IP=AB27 c. ES=DE21 & DI=D75F d. SS=FF5C & BP=92B8 e. DS=DC67 & CX=2FE8
in 80886 microprocessor Suppose that. DS = 0200H, BX = 0300H, and DI-400H Determine the memory address accessed by each of the following instructions, assuming real mode operation: (1) MOV AL,[1234H] (2) MOV AX,[BX] (3) MOV [DI]AL
Assume that the state of the 8088’s registers and memory just prior to the executionof each instruction in problem 15 is as follows: * in photos*What result is produced in the destination operand by executing instructions (a)through (k)? *only b,c,e,g* b) ADC SI, AX(c) INC BYTE PTR [0100H] (e) SBB DL, [0200H] (g) NEG BYTE PTR [DI]+0010H
Compute the physical address for the specified operand in each of the following instructions from previousproblem. The register contents and variables are as follows : (CS) = 0A0016, (DS) = 0B0016, (SI) =010016, (DI) = 020016 and (BX) = 030016.a) Destination operand of the instruction in (c)b) Source operand of the instruction in (d)c) Destination operand of the instruction in (e)d) Destination operand of the instruction in (f)e) Destination operand of the instruction in (g)
Q1:Suppose the initial physical address of a segment register is given by 0E41:A02EH. Determine the physical address, base and final address of that segment register of 8086 microprocessor
333: E8B3 8B3: 0A12 A12: 2153 Since the contents of the relevant addresses are 333 in the basic computer given above, the initial value of the PC is 333; When fetching and executing an indirectly addressing ISZ instruction, write the contents of the following registers in hexadecimal (hex) format for the T5 time. AR ........... DR......... IR ........... PC ........... SC ...........