esign a pneumatic circuit diagram for a double-acting pneumatic press by considering the functions and features of press as stated below. for initial startup, a choice of three manual (hand) push valve selection for the extension motion,  and automatic retraction function after 4 sec. of delay at the full extension position,  position sensed control both at the retraction and extension positions,  It is only to be extended if the actuator of the press is at the fully retracted position (AND fuction),  It should only work if pressure is above 6 bar on main pressure line. Features:  Complete air service (Air preparation) unit on the main pressure line,  manual switch on and off valve on the main pressure line for total circuit control.

esign a pneumatic circuit diagram for a double-acting pneumatic press by considering the functions and features of press as stated below. for initial startup, a choice of three manual (hand) push valve selection for the extension motion,  and automatic retraction function after 4 sec. of delay at the full extension position,  position sensed control both at the retraction and extension positions,  It is only to be extended if the actuator of the press is at the fully retracted position (AND fuction),  It should only work if pressure is above 6 bar on main pressure line. Features:  Complete air service (Air preparation) unit on the main pressure line,  manual switch on and off valve on the main pressure line for total circuit control.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter54: The Operational Amplifier

Section: Chapter Questions

Problem 7RQ: Name two effects of negative feedback.

See similar textbooks

Similar questions

A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
A CNC machine tool table is powered by a servomotor, ball screw, and optical encoder. The ball screw has a pitch = 7.5 mm and is connected to the motor shaft with a gear ratio of 12:1. The optical encoder is connected to the ball screw and generates 200 pulses/rev of the screw. The table must move a distance of 300 mm at a feed rate = 450 mm/min. (a) Determine the pulse count received by the control system to verify that the table has moved exactly 300 mm. Also, what are (b) the pulse rate and (c) motor speed that corresponds to the specified feed rate?
For the following automatic control systems commonly encountered in daily life, identify the devices that perform the measurement (M), decision (D), and action (A) functions, and classify the action function as “On/Off’ or “Regulating” (time-varying until reaching a setpoint). Also, draw a sketch of the control loop for each system and determine whether the control is feedback or feedforward. Automatic sprinkler system for fires Automobile cruise speed control Refrigerator
If one node is observed at a frequency of 1000 RPM, during a whiring of a simply supported long slender rotating shaft. The first critical speed of the shaft in RPM is ______?
A stepping motor with 240 step angles is coupled to a leadscrew through a gear reduction of 5:1 (5 rotations of the motor for each rotation of the leadscrew). The leadscrew has 6 threads/in. The worktable driven by the leadscrew must move a distance = 10.00 in at a feed rate of 30.0 in/min. Determine: Number of pulses required to move the table, and The required motor speed and pulse rate to achieve the desired table speed.
#24. Suppose there was a mating fit requirement with a tight size tolerance on the 3.000 OD above and then a separate location requirement to be met. Which coaxial control would you consider using? Explain?
Name two effects of negative feedback.
ass 4. vib . Give detailed description of at least two methods of vibration control.
(b) Give one example of a ratchet & pawl in design of any mechanical system? Give insight regarding application areas of hydraulic and pneumatic actuators?
An incremental optical encoder coupled to a robot wheel has 2880 slots. Find: a) change in angle when 1200 pulses counts are obtained b) number of pulse counts when the angular change is 5000 degrees
Q#04 (a) :What is Mechanism Design ? (b): Explain the Importance of Time Ratio and Timing charts in Mechanism design in detail.
What is the relationship of mass of block and angle of response.What can be conclude on the given data in the table.