Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear velocity and 2. Angular velocity NOTE: for JOINT 3 ( 03 ) only Connected to robot arm Pitch Roll Yaw Figure 2: Wrist assembly The known position and orientation of the end of the arm point is. [-G,S2C3 + S1S3 C,S2S3 + S1C3 |-S,S2C3 – C1S3 C2C3 C,C2 0] S,C2 S2 1 S,S2S3 + C,C3 -C2S3 °T3=°T¡'T2²T3=

Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear velocity and 2. Angular velocity NOTE: for JOINT 3 ( 03 ) only Connected to robot arm Pitch Roll Yaw Figure 2: Wrist assembly The known position and orientation of the end of the arm point is. [-G,S2C3 + S1S3 C,S2S3 + S1C3 |-S,S2C3 – C1S3 C2C3 C,C2 0] S,C2 S2 1 S,S2S3 + C,C3 -C2S3 °T3=°T¡'T2²T3=

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The inversion of the slider-crank mechanism shown in the figure is driven by link 2 at an angular speed and acceleration of 60 rad/s ccw and 240 rad/s2 cw, respectively. Find the velocity and acceleration of point B.|AO2|=75 mm, |BA|=400 mm, |O4O2|= 125 mm. (Using Complex Algebraic approach do the Position Analysis; Velocity Analysis and Acceleration Analysis then solve the problem please)
Please include explanation. A 6-MW offshore wind turbine has a capacity factor of 40%. It has a height of 120 m, and 107-m long blades. The angular acceleration is 1.388 rad/s2. Assume that the distance from the center of the turbine to the connection with the blade is negligible, and that the turbine starts from rest. At ? = 12 s, calculate the velocity and the acceleration for points (a) at half the length and (b) at the tip of the blade.
Consider the slider-crank mechanism shown. Crank AB is 0.500 m long and is rotating counterclockwise at 3.00 rad/s. Rod BD is 1.500 m long. 1. Which of the following gives the closest value of the speed of end B of crank AB? 2. If crank AB is rotating at a constant angular velocity, which body/bodies is/are in general plane motion?
In a four-bar chain ABCD. AD is fixed and is 150mm long. The crank AB is 90 mm long and rotates at 120 rpm clockwise while the link CD is 80 mm long and oscillates about D. BC and AD are of equal length. Find the angular velocity of link CD, when angle BAD = 60O. a) Draw the configuration diagram in appropriate scale. b) Determine the angular velocity (ωAB). c) Determine the linear velocity (Vba) d) Draw the velocity diagram in appropriate scale. e) Determine the linear velocity (Vcb), , and f) the angular velocity (ωcd)
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC,which in turn rotates about the terminal axis at O. At the instant shown, theangular velocity of the shaft OC is 10j rad/sec, and gear A is stationary. Deter-mine the angular velocity of gear B, and the velocity of a point D at the top ofgear B.
Crank 2 of the push-link mechanism shown in the figure is driven at w2=60 rad/s cw. Find the velocities of point B and C.|AO2|=150 mm, |BA|=800 mm, |O4O2|= 75 mm, |BO4|= 300 mm, |DA|=150 mm, |CD|=100 mm. (Using Complex Algebraic approach do the Position Analysis; Velocity Analysis and Acceleration Analysis then solve the problem please)
A slider on a rod is actauted by a lever with a slot that is rotating at a constant angular velocity of 2 radians per second. For the position shown, find the velocity of the slider (magnitude and direction)
Most gasoline engines in today's automobiles are belt driven. This means that the crankshaft, a rod which rotates and drives the pistons, is timed to the camshaft, the mechanism which actuates the valves, by means of a belt. Starting from rest, assume it takes t=0.0320s for a crankshaft with a radius of r1=3.25cm to reach 1750 rpm. If the belt does not stretch or slip, calculate the angular acceleration of crankshaft 2 of the larger camshaft, which has a radius of r2=6.50 cm, during this time period.
consider the slider-crank mechanism shown. Crank AB is 3.00 m long. Rod BD is 2.00 m long. The velocity at point B is 6.00 m/s, ↘45.0°. a. speed of the piston at D? b. On which area is the instantaneous center of rod AB located?
You walk along the beach towards a dock while your friend rows a boat towards the same dock on a flat lake. Your friend's boat approaches the dock on a straight course, but also rotates about its center-of-mass since your friend is not pulling evenly on the oars. If you knew your own velocity (vwalker), the magnitude of boat's angular velocity (thetaboat), and radius vector from yourself to your friend in the boat (rfriend) at any given time, you could use the following equation to calculate the your friend's velocity: vfriend = vwalker + (thetaboat)k x rfriend where k is a unit vector in the vertical direction. True False
what is the tension T1 in a cord attaching a baby to a scale? what is the tension T2 in the cord attaching the baby to the ceiling? The mass of a rocket sled is 2100KG and the force of friction opposing the motion is 640N. The thrust for the sled is 25900N. What is the acceleration in Metres per second second? A 1140 KG artillery shell is fired from a battleship,.W,hile it is in the barrel of the gun, it experiences an acceleration of 2.2 x 10^4 m/s^2. what net force is exerted on the artillery shell before it leaves the barrel of the gun in Newtons. What is the magnitude of the force exerted on the ship by the artillery shell in Newtons?
A circular saw blade 0.6 m in diameter starts from rest and accelerates with constant acceleration to an angular velocity of 100 rad.s-1 in 20 s. Find the linear velocity of a point in the rim of the saw when the angular velocity is 10 rad.s-1.