Ex #1] Given a gear of 16 teeth, 4 diametral pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the addendum, and the backlash is to be 2 percent of the circular pitch. Calculate the following, giving the results to 3 decimal places: a) the pitch diameter; b) the addendum and dedendum diameter; c) the whole depth; d) the backlash; e) the tooth thickness; and f) the space width. Given: A spur gear T= 16 teeth Add = 1/Pd Clearance = (1/8) addendum Backlash = 0.02 P Required: Determine the a) D, b) Add and Ded diameters, c) whole depth, d) backlash, e) tooth thickness, f) space width.

Ex #1] Given a gear of 16 teeth, 4 diametral pitch. The dedendum equals 1/P, inch, the clearance is to be one-eight of the addendum, and the backlash is to be 2 percent of the circular pitch. Calculate the following, giving the results to 3 decimal places: a) the pitch diameter; b) the addendum and dedendum diameter; c) the whole depth; d) the backlash; e) the tooth thickness; and f) the space width. Given: A spur gear T= 16 teeth Add = 1/Pd Clearance = (1/8) addendum Backlash = 0.02 P Required: Determine the a) D, b) Add and Ded diameters, c) whole depth, d) backlash, e) tooth thickness, f) space width.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 1deg in a length of 26 diameters. Compute the proper diameter if Do =2Di. Show your complete solution.
A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25 MN/m ^2 . What is the spced of rotation of the shaft in (r.p.m)? (b) If the solid shaft is replaced by the hollow shafl transmitting 100 kW at the same rotation speed of the solid shaft. The hollow shaft has a mean torque =5/6 of maximum torque with the angle of twist 0.35° per meter length of the shafl and G= 80 GN/m^2 Determine the dimensions ofr the hollow shaft if the internal diameter of the shaft is to be 80 % of the external diameter.
Design the outside and inside diameters for a hollow stell shaft subjected to a torque of 1,000,000 in-lb. The maximum shear stress developed in the shaft is not to exceed 8,000 psi. The inside diameter is to be 2/3 of the outside diameter. Calculate the angle of twist in degrees for a 14 foot length of this shaft. Answer: D(outside) = 9.259 inches, D(inside) = 6.176 inches, angle of twist= 1.39 degrees I'm unsure of how to solve this problem. Could someone help me walk through the process step-by-step? Thanks in advance.
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
Falcon company Nizwa is conducting a campus interview to you. You are asked to design the propeller shaft with the following specification. ) power tranmission = 270 kw (1) speed 65 rpm, () Maximum shear stress = 55 MPa (iv) diameter ratio = 1.78 (v) The maximum value of the twisting moment is 40% greater than its mean. Find, (i)The mean torque is (Unit is in Nm)=, (ii)The maximum torque is (Unit is in Nm)=. (iii) The outer diameter of the shaft (unit in mm) (iv) The inner diameter of the shaft (unit in mm)
Data:P = 2 kipd = 3.6 inchw = 305 millimeterst = 0.03 meterr = 5.08 centimeterh = 0.6667 feet a) Calculate the maximum static stress in the material (in MPa). b) Estimate the theoretical stress concentration factor at the fillet c) Estimate the theoretical stress concentration factor at the hole
Find the diameter of a shaft to transmit twisting moments varying from 800 N-m to 1600 N-m. The ultimate tensile strength for the material is 600 MPa and yield stress is 450 MPa. Assume the stress concentration factor = 1.2, surface finish factor = 0.8 and size factor = 0.85.
Design a hallow shaft (Diameter and length) that develops 80 kW of power while rotating at a speed of 4000 rpm. The design constrains are as under:The angle of twist not to exceed 0.200Shear stress is not to exceed 480 MN/m2The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m2.
A turbine shaft transmits 500 kW power at 900 rpm. The permissible shear stress is 80N/mm² while twist is limited to 0.5º in a length of 2.5 m. Take G = 0.8x10⁵ N/mm², on thebasis of torsional rigidity;i.Determine diameter of shaft if solid shaft is used.ii.If hollow shaft is chosen with di/do = 0.6, determine the suitable diameters of theshaft. please write with ball pen.. thank you
Please don't copy Find the torque and power transmitted by a 100 mm diameter shaft, if maximum angle of twist and length of shaft are 1.2° and 2 m. Take G = 70 GPa, speed of shaft = 230 r.p.m.
Steel bar in shape, AAB 600 mm and ABc = DACD3D 1200 mm2 are made of two stages. Determine the displacement at end A in (mm).
Please solve clearly step by step otherwise don't attempt.will report. A shaft is required to transmit 285 kW power at 255 r.p.m. The maximum torque may be 1.8 times the mean torque. The shear stress in the shaft should not exceed 46 MPa and the twist 1.2° per metre length. Determine the diameter required if, (i) The shaft is solid