Example 2: Calculate the voltages on resistors R₂ and R3, the voltage on the inductor L and the current flowing through the inductor L, select the polarity (orientation) of the voltages/currents according to the picture. The circuit is in the DC steady state. 10 mA, R₁ 330 f2, R₂ = 2 k2, R3 = 3 kf, L = Parameters of components: U= 10V, I 100 mH, C = 1 μF. RI R3

Example 2: Calculate the voltages on resistors R₂ and R3, the voltage on the inductor L and the current flowing through the inductor L, select the polarity (orientation) of the voltages/currents according to the picture. The circuit is in the DC steady state. 10 mA, R₁ 330 f2, R₂ = 2 k2, R3 = 3 kf, L = Parameters of components: U= 10V, I 100 mH, C = 1 μF. RI R3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

IN THE CIRCUIT SHOWN, CONSIDER THAT V1=20 VDC, R1=1000 Ω, R2=3000 Ω, R3=3500 Ω AND C=1 mF.DETERMINE:A) THE TIME IT TAKES FOR THE CAPACITOR TO REACH ITS FINAL VALUE (5T), WHEN SWITCH 2 (INT 2) IS IN POSITION A AND SWITCH 1 (INT 1) IS CLOSED AT t=0,B) THE ENERGY STORED BY THE CAPACITOR ONCE IT HAS BEEN FULLY CHARGED WITH THE SAME POSITION OF SWITCHES AS ITEM A)C) ONCE THE CAPACITOR HAS BEEN FULLY CHARGED WITH SWITCH 1 CLOSED, SWITCH 2 MOVES POSITION (GOES TO B) AT A NEW t=0. NOW DETERMINE THE VALUE OF THE VOLTAGE ON THE CAPACITOR AT t=3.5 SECONDS
Can you please help with this question? The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
Consider an LRC series circuit with a resistance of 2.5 ohms, capacitance of 0.1 farad, aninductance of 0.1 henry and electromotive force, volts. Given thatAssume there is no initial charge and no initial current on thecapacitor.The equation of the charge q(t), on the capacitor at any time t q(t)=C1e−5t+C2e−20t+0.05cost+0.2sint . (Do not solve the coefficients). a) State the equation of the current, i(t). b) State the transient and the steady-state current. c) What is the current after a long time.
An RC circuit with a capacitance of 1E-1 farad, and a resistance of 2Ω, has an EMF of E(t)=4cos(t) volts applied to it. a. Find the charge on the capacitor, q(t), with q(0)=6/13, and the subsequenct current, I(t). Solve the problem mathamatically (DE) and try to restrain yourself from solving it using your physics knowledge.
The circuit shown is at steady state before the switch closes. The inductor currents are both zero before the switch closes (i1(0) = i2(0) = 0). The voltage across the 2H-inductor is 4e-5t V for t > 0, otherwise 0V for t < 0. (a) Determine the inductor currents i1(t) and i2(t) for t ≥ 0. (b) Determine the energy stored by each inductor 200ms after the switch closes. (c) In the equivalent inductor (for the parallel inductors) determine the (i) current and the (ii) energy stored for 200 ms after the switch closes. Answer: 0.4(1 − e−5t) A, 0.1(1 − e−5t) A, 16.0mJ, 63.9mJ, 316mA, 79.9mJ
The triangular voltage pulse shown below is applied to a 200 mF capacitor. a) Write the expressions thatdescribe vc(t) in the five time intervals t < 0, 0 ≤ t ≤ 2 , 2 ≤ t ≤ 6, 6 ≤ t ≤ 8, and t > 8. b) Derive theexpressions for the capacitor current, power, and energy for the time intervals in part (a).
Solve the circuit by obtaining the state equation. The initial condition voltage value of the capacitance element is VC (0) = 1Volt. R1 = R2 = R3 = R4 = 1Ω, E = 3Volt. State the core solution and the forced solution components in the solution you obtained.
The circuit shown below is an underdamped system, and the current through the inductor has the form iL(t)=e^at ( ) (K1sinwt + K2coswt ) for t≥0 a. Determine the numerical values, including signs, of a and w b. If the initial conditions are iL(0) = 1A and Vc (0) =12V , determine the numerical values, including signs, of K1 and K2 c. Using the numbers determined above, write out the complete expression for iL(t)
Design a single circuit element containing one inductor, one capacitor and one resistor with v(t) of = vt=4+2e-3tV and it=-3e-3tA for t>0 . Also specify the value of the inductance, capacitance and the resistance of the tree element
a) Obtain the expression of v0 (t), for all t> 0, for the network of the figure shown: b) Without applying the step-by-step method and with the result obtained above, find the expression for the voltage across the inductor, for all t> 0.
In the circuit shown below, the switch has been open a long time and the circuit is initially in steady-state. At t=0, the switch is closed. R1=0.2Ω, and R2=0.4Ω. The batteries have EMFs E1=1V and E2=3V. The capacitor has capacitance 10 μF. Hint: What is the voltage on the capacitor just before the switch is closed? Note that there is a voltage drop over the open switch. a) What is the voltage over the capacitor before the switch is closed? b) Draw the Thevenin equivalent circuit as seen by the capacitor. c) What is the time constant for charging the capacitor? d) What is the voltage on the capacitor as a function of time?
An inductance of 1 H, a resistance of 8 Ω and capacitance of 0.04 F are connected in series with a variable voltage E = 50 sin 3t. Find the current and charge in the system, given the initial conditions q = 0 and l = 0 when t = 0, using method of solution of higher order linear ordinary differential equation.