Example 32.81. 4 5-kVA distribution transformer has a full-load efficiency at unity p.f. of 95 %, the copper and iron losses then being equal. Calculate its all-day efficiency if it is loaded throughout the 24 hours as follows: No load for Half load for Assume load p.f. of unity. Quarter load for Full load for 10 hours 7 hours 5 hours 2 hours (Power Apparatus-I, Delhi Univ. 1987)

Example 32.81. 4 5-kVA distribution transformer has a full-load efficiency at unity p.f. of 95 %, the copper and iron losses then being equal. Calculate its all-day efficiency if it is loaded throughout the 24 hours as follows: No load for Half load for Assume load p.f. of unity. Quarter load for Full load for 10 hours 7 hours 5 hours 2 hours (Power Apparatus-I, Delhi Univ. 1987)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.54P: An infinite bus, which is a constant voltage source, is connected to the primary of the...

See similar textbooks

Similar questions

A network is composed of the utility having Ssc=250MVA, and an 2000KVA transformer, rated at 20KV/400V (no load), whose voltage impedance is 7%, and whose load losses are 15750watts. the short circuit at the secondary of the transformer using the impedance method is: a)27.01KA b)None of these c)25.8KA d)30KA
Find the all-day efficiency of a 500 kVA distribution transformer whose copper loss and iron loss at full load are 4.5 kW and 3.5 kW respectively. During a day of 24 hours, it is loaded as follows: 6 hours, 400 kW, 0.8 pf; 10 hours, 300 kW, 0.75pf; 4 hours, 100 kW, 0.8 pf and no-load for 4 hours. Provide the following parameters in order: Wcu, Wco, Wout, Eff ALL-DAY
1) A 600 V source feeds a 480 V load with a transformer Conventional 5000 VA, 480/120 V. Consider the ideal transformer. a) Calculate the apparent nominal power of the transformer in the connection as Autotransformer. b) Calculate the currents on the high voltage side and on the low voltage side in these conditions. c) Calculate the current in the common coil in the connection as Autotransformer.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
Solve the following problems with complete solutions and unitsusing two(2) decimal digits. Use your own analysis andcomputations. 2. A 3-phase transformer, ratio 33/6.6-kV, Δ-Y, 2-MVA has a primary resistance of 8 Ω per phase and a secondary resistance of 0.08 Ω per phase. The percentage impedance is 7%. Calculate the secondary voltage with rated primary voltage and hence the regulation for full-load 0.75 power factor lagging conditions.
Each motor is rated at 80 hp but is only loaded mechanically as follows: Motor # % Loading 1 40 2 50 3 70 The relationship between % of full load for each motor and efficiency (they are all the same) is given by the graph below: a) What is the minimum required transformer rating in kVA? b) By what percentage could the required transformer rating be reduced if a capacitor bank were installed in parallel with the motors, improving the power factor of the loadcentre to unity?
For the linear transformer in Fig. 13.26(a), find the equivalentnetwork.
A 5000-kVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent anda perunit reactance of 5 percent (data taken from the transformer’s nameplate). The open-circuittest performed on the low-voltage side of the transformer yielded the following data:VOC = 13.8 kV; IOC = 15.1 A; POC = 44.9 kW.(a) Find the equivalent circuit referred to the low-voltage side of this transformer.(b) If the voltage on the secondary side is 13.8 kV and the power supplied is 4000 kW at 0.8 PFlagging, find the voltage regulation of the transformer. Find its efficiency
A.1. A gas likely to be used in an inert-gas system of a power transformer isA. oxygen.B. hydrogen.C. air.D. nitrogen.A.2. In the design of transformer windings, creepage between conductors and core yokes is prevented byproviding,A. keep-back distance.B. vertical oil ducts.C. separation sticks.D. bushing terminals.
A single-phase 100-kVA, 2,400/240 V, 60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240 V secondary winding, absorbs 80 kVA at 0.8 power factor lagging and is at 230 V. Assuming an ideal transformer, calculate the following:(a) primary voltage;(b) load impedance;(c) load impedance referred to the primary;(d) the active and reactive power supplied to the primary winding.
A Transformer with 10:1 ratio and rated at 50-kVA, 2400/240-V, 50-Hz is used to step down the voltage of a distribution system. The low-tension voltage is to be kept constant, if the transformer has: R = 2.2 0, R2 = 0.014 Q, X, = 4.1 0, X2 = 0.03 0, then, a. What load impedance connected to low-tension side will be loading the transformer fully. b. Calculate the equivalent resistance as referred to primary. c. Calculate the equivalent reactance as referred to primary. d. Calculate the equivalent impedance as referred to primary. e. Calculate the total Cu loss.
A 120:480-V, 10-kVA step-up two-winding transformer is to be used as an autotransformer to supply a 120-V circuit from a 600-V source (a step-down autotransformer). When it is tested as a two-winding transformer at rated load, unity power factor, its efficiency is 97.9 %. 1.Show the connection diagram of the transformer converted as an autotransformer and identify which is the series winding Nse and the common winding Nc.