Еxample (a) A Brinell hardness measurement is made on a ductile iron (100– 70–03, air- quenched) using a 10-mm-diameter sphere of tungsten carbide.A load of 3,000 kg produces a 3.91-mm-diameter impression in the iron surface. Calculate the BHN of this alloy. (The cor- rect units for the Brinell equation of Table 6.9 are kilograms for load and millimetres for diameters.)

Еxample (a) A Brinell hardness measurement is made on a ductile iron (100– 70–03, air- quenched) using a 10-mm-diameter sphere of tungsten carbide.A load of 3,000 kg produces a 3.91-mm-diameter impression in the iron surface. Calculate the BHN of this alloy. (The cor- rect units for the Brinell equation of Table 6.9 are kilograms for load and millimetres for diameters.)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A copper specimen subjected to the Brinell Hardness Test using hardened steel ball indenter of diameter 13 mm and the indentation diameter 3.78 mm is measured using an optical magnifying lens with a ruler. Draw the Brinell Hardness Test setup neatly and determine the force applied on the specimen. Take Brinell Hardness Number for copper as 1037. Surface Area of Indentation (in mm2) = Applied Force (in N) =
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
The block shown is made of a magnesium alloy for which E=X2GPaand ϑ=0.35. Knowing that σx= X1 MPa, determine (a) the magnitude of σyfor which the change in the height of the block will be zero, (b) the corresponding change in the area of the face ABCD, (c) the corresponding change in the volume of the block.
A Brinell hardness tester with a diameter of 10 mm and a load of 500 kg gives an impression with a diameter of 1.62 mm in a steel alloy. Calculate the Brinell hardness (HB) in the steel alloy
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
Steel, Brass, and Copper rods are connected as shown in the figure. Initially, the temperature was 15 degrees Celsius and the stress on the bars is zero. Eventually, the temperature increased to 25 degrees Celsius. Determine the normal stress on the steel due to the change in temperature. Steel Brass Copper Est = 200 GPa ast = 12(10-)/°C abr Ebr = 100 GPa 21(10-")/°C acu = 17(10-")/°C Ecu 120 GPa %3D %3D Acu 515 mm? 200 mm? Abr = 450 mm2 Ast -300 mm -200mm 100 mm O 20.11MPA, C O 15.57MP., C O 8.94MPA, c O 35.02MPA, C
(b) (i) A tensile test specimen made from 0.4% C steel has a circular cross section of diameter d mm and a gauge length of 25 mm. When a load of 4500 N is applied during the test, the gauge length of the specimen extends to 25.02 mm. If the Young's Modulus of the steel is 199 GPa, calculate the diameter of the tensile test specimen used. 4
The following information about the o-e curve is given for a steel alloy. E = 0.001527 at o = 300 MPa and ɛ = 0.003054 for o = 600 MPa. (a) Draw the stress-strain diagram and calculate the E for this alloy.
Question One (Compulsory) The following results were obtained during a tensile testing of a highiy ductile bronze specimen: Stress 249 (MPa) Strain 0.001 0.024 0.035 0.041 0.049 0.059 0.074 0.14 498 746 870 995 1119 1244 1368 1493 1552 1552 14 0.43 0.63 0.8 0.9 (B: The original diameter of the test piece was 15 mm and the gauge length was 75 mm. The diameter a fracture was 12.5 mm. Using the graph paper provided, carry out the following: i. Plot the engineering stress - strain diagram ii. Determine the maximum stress on the specimen ii. Calculate the force at ultimate tensile strength point iv. Determine the yield strength Calculate the % elongation V. vi. Calculate the true stress and true strain at fracture point.
(Solid Mechanics) A setup for single-edge-notch-bending (SENB) tests is shown below. Support rollers provide frictionless contact with the specimen, while a load is applied at the middle of the top surface of specimen. The thickness of the specimen is 10 mm and the height W 10mm. The properties for this ductile alloy are E = 70 GPa, v=0.3, σᵧ = 400 MPa, Kᵢ? = 25 MPa.m¹/². (1) Ignore any crack or defects in the material, what is the maximum static force that the specimen could carry before failure? (2) A cyclic load of low amplitude 2.8 kN is applied. Because of the cyclic load a defect is nucleated on the edge and grows into a fatigue crack of 2 mm length shown in the right. If the cycling is interrupted, what is the maximum static tensile force that the specimen could carry? (3) With more cycles, the fatigue crack keeps growing. Estimate the critical crack length (a range is fine) at which the plate will fail from the low-amplitude cyclic load 2.8 kN only. (maximum two iterations are…
The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. If the specimen is loaded until it is stressed to 70 ksi, determine the approximate amount of elastic recovery and the increase in the gage length after it is unloaded. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0 04 0.08 0.12 0.16 0.20 0.24 0.28 0 0005 0.0010.0015 0.002 0.0025 0.0030.0035
Two uniform spheres are positioned as shown. Determine the gravitational force F which the titanium sphere exerts on the copper sphere. The value of R is 30 mm. Assume a = 4.9, b = 2.3, 0=29° y R 1 aR Titanium Copper bR - X