Example: show the control signals needed to perform Add R1, R2, RO using: a. Three bus organization b. One bus organization Solution: a. Three bus organization Step Instruction type Micro-operation Control Inst-x Ro (R)+(R) Select Ry as source I on out busl (R, cut-bus I) Select R; as source 2 on out-bus2 (R out-bus2) Select Ro as destination on in-bus (Ro in-bus) Select the ALU function to

Example: show the control signals needed to perform Add R1, R2, RO using: a. Three bus organization b. One bus organization Solution: a. Three bus organization Step Instruction type Micro-operation Control Inst-x Ro (R)+(R) Select Ry as source I on out busl (R, cut-bus I) Select R; as source 2 on out-bus2 (R out-bus2) Select Ro as destination on in-bus (Ro in-bus) Select the ALU function to

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter6: System Integration And Performance

Section: Chapter Questions

Problem 34VE

See similar textbooks

Similar questions

Give the following about BUS TOPOLOGY: Advantage Disadvantage When to use?
Two disadvantages of the Bus topology that you should describe are difficulties in reconnection and fault isolation.
4) Obtain the truth table for a 2-to-1 word-sized mux where the two input buses and output bus are all 2-bits wide. Use IN0_1, IN0_1, IN1_0, IN1_1, S for the inputs and OUT_0 and OUT_1 for the outputs. Obtain the schematic diagram for a possible implementation of such a mux following the example given in Figure 3.3
4) Obtain the truth table for a 2-to-1 word-sized mux where the two input buses and output bus are all 2-bits wide. Use IN0_1, IN0_1, IN1_0, IN1_1, S for the inputs and OUT_0 and OUT_1 for the outputs. Obtain the schematic diagram for a possible implementation of such a mux following the example given in Figure 3.3 correctly.
Two of the disadvantages of the Bus topology that you should describe are the challenges in reconnection and fault isolation.
Construct a hardware circuit by using common bus architecture to implement the following Register Transfer Languages. P: A1 A2 Q: A2 A3 R: A4 A1 S: A3A4, A1A4 Where A1, A2, A3, A4 are one-bit register
Draw the control unit and datapath for the following algorithm that returns an integer value. The function takes two points (x1, y1) and (x2, y2) and computes the equation for a line. It then evaluates and returns ynew for the parameter xp using that line. Use a 16-bit data bus. Show your work; label and clearly mark your diagram. Do not implement this in VHDL. int PredY(int x1, int y1, int x2, int y2, int xp) { int m, b, ynew; if (x1 – x2) <> 0 { m = (y1 - y2) / (x1 - x2); b = y1 - m * x1; ynew = m * xp + b; return(ynew); } else { return(65535); // that's a 16-bit FFFF } }
Write any three differences between star & bus topologies.
The bus topology has high utilization under heavy traffic. A) True B) False
Q1. Show the micro-operations for the execution of each of the following instructions in One-bus, Two-Bus, and Three-bus organizations: a. Load R1, X One-bus Two-Bus Three-bus b. Subtract R1,X,Ro One-bus Two-Bus Three-bus
Analyze the similarity and difference of the Verilog implementation of bus using tri-state buffer and multiplexer.
Considering the 3 bus SRC write the concrete RTN and control sequence for and ra,rb,rc.Explain why is it different from that of 1 bus SRC