Hydraulic and pneumatic Exercise: 06For the system given infigure,force required to drive a1000 N load.400 mmdeterminethe90°90Cylinder500 mmExercise: 07For the crane system, determine thehydraulic cylinder force required tolift a 2000 N load.3 m2000 N45°B.75HomeEndInsertDeBa

Name: Hydraulic and pneumatic Exercise: 06For the system given infigure,forc
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Hydraulic and pneumatic Exercise: 06For the system given infigure,force required to drive a1000 N load.400 mmdeterminethe90°90Cylinder500 mmExercise: 07For the crane system, determine thehydraulic cylinder force required tolift a 2000 N load.3 m2000

Answered: Image /qna-images/answer/c467dee9-f68c-4d26-928f-c5521b38d980.jpg

Answered: Exercise: 06 For the system given in…

Engineering

Mechanical Engineering

Exercise: 06 For the system given in figure, determine force required to drive a 1000 N load. 400 mm the 90° 90 Cylinder 500 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.99P: The 400-kg drum is held by tongs of negligible mass. Determine the magnitude of the contact force...

See similar textbooks

Similar questions

Find the tension T in the cable when the 180-N force is applied to the pedal at E. Neglect friction and the weights of the parts.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The 400-kg drum is held by tongs of negligible mass. Determine the magnitude of the contact force between the drum and the tongs at D.
The homogeneous plate of weight W is suspended from two cables. Determine the force P that is necessary to keep the plate in the position shown.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
The spring attached to the homogenous bar of weight W is undeformed when =0. Determine the smallest spring stiffness k for which the =0 equilibrium position will be stable. Use W = 10 lb, a = 24 in., and b = 6 in. Assume that the spring remains horizontal, which is a valid approximation if is small.
The hoist supports the 155-kgkg engine. -Determine magnitude of the force the load creates in member FBFB, which contains the hydraulic cylinder HH. -Determine magnitude of the force the load creates in member BDBD.
The figure shows a high-pressure hand pump usedfor boosting oil pressure in a hydraulic line. Whenthe handle is in equilibrium at ? = 15° under theaction of a force P = 120 N, determine the oil pressure p which acts on the 46-mm-diameter piston. (Pressure on the top of the piston is atmospheric.)
*Show clearly all pertinent solutions and state the assumptions made, if any. Alie Abdul is nearing completion in assembling the giant robot doll. He needs to exert a 408.75N force on the pulley cable to lift the doll robot’s head (50kg) to attach to its body. Note: robot head’s weight is acting in the z- direction. a. Draw the FBD of the robot’s head. b.Determine the tensions in the four cables. Assume pulley E is frictionless.
The homogeneous cylinder of weight W = 100N rests in a frictionless right-angled corner. Determinethe contact forces NA and NB if θ = 30°.
If the h0m0gen0us bar in equilibrium weighs 300N, what is the magnitude (N) of the tensi0n supp0rt at p0int C?
The homogenous bar A having a mass of 18 kg is 2 m long and is inclined at 60 degrees with the horizontal plane. The mass M of 7 kg is connected by the rope to the bar. The rope leaving the bar is horizontal. The coefficient of friction between the rope and the drum B is 0.20. What is the minimum coefficient of friction between the bar and the plane for equilibrium? Give solution. (Ans. coefficient of friction = 0.284)