lb. The shaft diameter is 1.75 inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, find A. Force that will shear the pin, kN B. Shear pin diameter, mm
Q: Two concentric, helical compression springs support a 6.5-kip load. The larger spring has an outside…
A:
Q: The end of a 2.5 in diameter steel shaft is milled to two flats (one flat on the top and one flat at…
A: Given data as per question Diameter of shaft =2.5 in Length of shaft =2 in Torque applied =750 lb.in…
Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…
A:
Q: A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34 in.…
A:
Q: A flange coupling connects two 2” diameter shafts. The flanges are fitted with 6 bolts of SAE 1040…
A: (a) Torque = power/speed = 45 * 550/(300 * 2π/60) = 787.82 lb ft = 9453.8 inch lbs Torque…
Q: The one end of a hollow square bar whose side is 10.17 with thickness is 1.17 under a tensile stress…
A:
Q: Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter…
A:
Q: A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa.
A: Dear student, there are multiple question and we are suppose to solve only one question. Also in…
Q: 10/.. find the shear stress in bolts 4 80 kN 80 kN -O- O--O- 300 mm
A: Write the expression for the load acting on the riveted joint.
Q: Find the diameter of a solid steel shaft to transmit 18 kW at 990 r.p.m. The ultimate shear stress…
A:
Q: A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig.…
A: Diameter D = 450 mm Kb = 2 Kt = 1.5
Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…
A:
Q: A rotating shaft, 15 mm in diameter, is made of plain carbon steel FeE 400 (Sy 400 N / mm2). It is…
A: Diameter,D = 15 mm Sy = 400 N/mm2 Tensile force = 3000 N Torsional moment = 65 Nm Bending moment =…
Q: A rotating shaft of 25-mm diameter is simply supported by bearing reaction forces R1and R2. The…
A:
Q: (7) The drive of an outboard motor which rotates @ 5,000rpm is supported by a spline in the…
A:
Q: [40] Problem 1: A bearing supports a 28mm diameter solid steel torsion rod (plan view shown in Fig.…
A: Diameter = 28 mm Arm= 300 mm Vertical load =2500N To find. Total stress
Q: Problem 2 The landing gear of an aircraft is depicted in Figure below. What are the required pin…
A: Apply the conditions of equilibrium ∑MA=0By×16=-10sin15°×(16+16)By=-5.176 kips…
Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…
A:
Q: Problem Ħ 44. Given: 145 kg SONE for: Stress in each pin pin A pin o weight of beam = lo0 kg pin A…
A:
Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…
A: Given Data:- Side(s) =0.1m = 3.93inch.......considering the unit as meters Thickness (t) =0.01m =…
Q: A steel rod 8 mm in diameter is under the action of a tensile force (P) of 600 Newton. Calculate the…
A: Tensile stress is given by the following formula, Sigma=P/A Where P is the tension force and A is…
Q: A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. 400…
A:
Q: The one end of a hollow square bar whose side is 0.1 with 0.01 thickness is under a tensile stress…
A:
Q: A diagrammatic representation of a universal joint is shown, two yoke parts, the type being similar…
A:
Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…
A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…
Q: PROVIDE FREE-BODY-DIAGRAM IN EVERY LETTER. Show clear hand writing and complete solution. Thank you…
A: Given: The load, P = 275 kN
Q: A steel shaft is to be manufactured either as a solid circular solid bar or as a circular tube. The…
A:
Q: Problem 121 Referring to Fig. P-121, compute the maximum force P that can be applied by the machine…
A:
Q: Problem 7: Analyse to determine the maximum service tensile live load force that can be supported by…
A: Calculation of diameter of hole dA=diameter bolt +side clearance =0.7+18=0.8336 in
Q: Find the load that can be lifted by applying a force of 200 N at the end of 450 mm long lever of…
A: Here we have provided data from the question, Force applied at the end of lever, P=200 N Length of…
Q: Q3. A welded steel cylindrical drum made of a 15mm thickness plate has an internal diameter of 1.50…
A:
Q: Problem 3: Compute the factors of safety for the configuration. Bar and pin dimensions, limiting…
A:
Q: simple turnbuckle arrangement is constructed from a 40 mm outside diameter tube threaded internally…
A: GivenTurnbuckle area=πdo2-di2/4do=40 mmdi=25 mm
Q: The figure shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is…
A:
Q: A 0.375 in. diameter solid steel shaft supports two pulleys as shown in Figure P9.11. The shaft has…
A: Givend=0.375 inL=9 inP=60 lb
Q: 1. A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850…
A: Given: The maximum torque is 850 in-lb. The diameter of the shaft is 1.75 in. Ultimate stress is…
Q: shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is…
A: Given that ,Power P=75kWspeed N=300 r.p.m Distance b/w bearing =300mm=3mshear stress for shaft…
Q: Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft…
A: Given data: The diameter of the shafts is d = 35 mm The number of bolts is n = 8The diameter of the…
Q: A 1000mm cast iron pulley is fastened to a 112mm shaft by means a 28mm square key 160mm long. The…
A: given data :- shear stress = 200Mpa bearing stress = 660 Mpa length of key = 160 mm width and…
Q: Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The…
A: Given DataP=15kWN=1000 rpmTs=60MPaTbolt=25 MPa
Q: Problem 2: Let FA=100 N and Fc= 208.33 N for the shaft below. The bearings D and B act as pin…
A: Given data as per the question FA =100 N FC = 208.33 N Yield strength =276 Mpa diameter of shaft =8…
Q: Fill in the blanks: Find the size of wire in mm if the maximum design stress is 425 000 KPa. A mass…
A: Answer: The size of the wire (i.e. diameter of wire used for helical spring) is 7.74 mm.
Q: Assume you have a 30 mm in diameter AISI 1040 steel shaft welded on a rigid surface. Forces applied…
A: given; →diameter(d)=30mm=0.03m→applied torque (T)=40Nm→applied mass for bending (mb)=100kg→mass of…
Q: PROBLEM 3 Two shafts are being connected by a coupling which is held together by four 3/4-in…
A:
Q: a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use…
A:
Q: Mohr circle exercise: (values are in MF 30 5 15 а. Draw MC for a given stress state. b. What is the…
A: Given:Sx=30 MPaSy=15 MPaζxy=5 MPa
Q: "A bolt assembly is experiencing 1000 lb of force. The diameter of the head is 5in, bolt diameter is…
A: Calculated shear stress in psi .
Q: The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile…
A:
Problem 1 only, solve carefully, include the units and dra the diagram. Thanks! . A taper pin is used to fix a lever to a shaft, if it is to transmit a maximum torque of 850 in-lb. The shaft diameter is 1.75
inches and has an ultimate stress of 60,000 psi, if the factor of safety is 3, find
A. Force that will shear the pin, kN
B. Shear pin diameter, mm
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images
- A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
- Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wiresQ // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined modelThe stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
- The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to bearing stress. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material. N = 47,The one end of a hollow square tube whose side is ( 10 + N/100 ) in with ( 1 + N/100 ) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable stress) = 243 ksi for pin material. N = 47,Two circular rods of 50mm diameter are connected by a knuckle joint, by a pin of 40 mm in diameter. If a pull of 120 kN acts at each end, find the tensile stress in the rod and shear stress in the pin.
- The one end of a hollow square tube whose side is (10+N/100) in with (1+N/100) in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ_all=243 ksi for pin material.N = 47,A hollow cylinder of external diameter 50 mm and internal diameter 30 mm is subjected to tensile load of 150 kN. Then the tensile stress is _____________ MPaCalculate each of the following under 20 kN load on a structure given below where all pins have a diameter of 10 mm. a) What is maximum stress on bar BD? b) Check the Pin strength at Location D against shearing. (Use ?Y=300 MPa, n=2 - factor of safety for Pin). Is it secure/safe or not? c) Check the Pin and Bearing strength against shearing at Location C. Are they secure/safe or not? (Use ?Y=300 MPa, n=2 - FOS for pin/bearing and ?Allow=300 MPa for bearing).