Explain Mixed Modes?

Q: quaton- dr dt %3D ovrdedt ind: rt) with Hhe informatron pronded

A:

Q: What is the difference between LEFM and EPFM?

A:

Q: In bode plot, the value of phase of G(wj) at the gain crossover frequency is -125 degrees, the PM of…

A: Given, Phase angle at the gain crossover frequency = Φ = -125 oC   Phase margin (PM) is given by,…

Q: For each state of an n-channel enhancement-mode MOSFET that follows, determine what operating region…

A: A n-channel MOSFET is made up of a p-type substrate that is implanted with two n-type materials that…

Q: explain the main benefit of a heat-recovery VRFsystem

A: VRF systems are also known as variable refrigerant flow. There are different kinds of VRF systems;…

Q: natural frequencies -

A: m=50 kg                                   Jo=100 kg-m2k1=500N/m…

Q: Which of the following is not an example of recording devices? O a a. CRO O b. Digital Recorders O.…

A: Amongst the given devices, Magnetic tape is a recording device. It is developed from a thin,…

Q: Define RADIO?

A: Radio is a technology developed to communicate and share signals by transmitting electromagnetic…

Q: @ Déscuss MDethenol as a luel is the Transpustation sector

A:

Q: 3. What is the “hunting" vibration mode? 4. What is the critical wave velocity?

A: Hunting vibration or oscillation is a phenomenon where a system tends to attain equilibrium by…

Q: he modulation index is said to be 1.8. What would you say for such a value? O a. under modulation O…

A:

Q: Resonance frequency of structural members can be detected with:

A: we will discuss vibration analysis of structural members

Q: Coefficient of Refraction The ndence du Coefficient of Transmission Coefficient of Absorption

A: Given question: Explain the coefficient of refraction, coefficient of transmission and coefficient…

Q: Obtain the Maxwell Relationships for:  dG = V dP – SdT

A:

Q: Discuss on main types of accumulators and explain any one with neat diagram.

A: Accumulators - It is part of hydraulic system which store hydraulic energy in the form of…

Q: If 60MHZ of total spectrum is allocated for a duplex wireless cellular system and each simplex…

A:

Q: Determine the two natural frequencies and mode shapes of thể two-mass syst

A: Given: To determine: Natural frequency mode shape

Q: 1. Explain the Scalar Control Method used in VFDS.

A:

Q: Does SC and BCC have the same unit plane of (1 0 0) like the picture below 83 a

A: Draw the (1,0,0) plane for the simple cubic unit cell.

Q: b) Describe and briefly explain the advantages of instrumentation ampliriers over differentiai…

A:

Q: 3)Explain how can we use the Linear Variable Differential Transformer (LVDT) as a. A flow…

A: LVDT is basically a transducer, which converts the rectilinear motion of the object to electrical…

Q: How it is generated Single sideband modulation

A: Single side band is a spacial type of amplitude modulation. In single side band both the carrier and…

Q: 41. Find the average value of the periodic waveform of Fig. 94 over one full cycle.

A:

Q: Explain a brief introduction to the angular transmitter mechanism and its application ?

A: Explanation As a circuit element, the angular transmitter mechanism is essentially a variable…

Q: Mechatronics Write the Boolean Expression for each of the following Figures: 1. 2. Page | 2

A: 1) A*B, since it is a AND gate

Q: 3. Discussion 1. What is the effect of the diode voltage drop on the output of the clipping circuit…

A:

Q: a) Distinguish between the characteristics of the two instruments in Fig. Q2(a). You may present…

A: Given questions are related to robotics engineering.

Q: f a 2 mV signal produces a 2 V output, what is the voltage gain?

A: Given      Input voltage, v = 2 mV = 2 × 10-3 V  Output voltage, V = 2 V  Find Voltage gain, A

Q: Ros (a) what are they used for, (b) what are the characteristics of each of them in terms of…

A: The Robot Operating System (ROS) is an open-source platform that assists academics and developers…

Q: Discuss the principle of accelaration

A: Principle of acceleration: A principle of acceleration is a term based on the fact that the demand…

Q: Discuss the effect of atmospheric air entry in VCRS?

A: The high pressure refrigerant vapour after getting compressed in compressor enters into condenser…

Q: er of transistors in a VLSI chip will increase e

A: Moore's Law asserts that the number of transistors on a microchip doubles every two years, while…

Q: What is natural frequency?

A: Natural frequency is the oscillation of mechanical or any system in the absence of any driving or…

Q: had a natural frequency of 20 cycles/second. What is the approximate fundamental frequency of…

A: Applying Dunkerly's principle, 1⁄(ω12)+1⁄(ω22)+1⁄(ω32) = 1/100 + 1/400 = 1/80 Therefore  ω1=80…

Q: what is the CW you are using in the quations , and where do you find it ?.

A:

Automation in manufacturing processes

The term automation refers to the technique through which the creation of an apparatus takes place using an automatic process or a system. Let us try to understand this with an example.