Ez 11 Abeno with dimenyins b=300, deboomm,andh-7oo mm , with z8 MPu, Carriesfuctor load 440KN ut mizspan. find the mue. s hearstrensth of the couercte (Vc) at the first critical sectionfor shear at a distance (d) from the suppert fesedsidgle concentrated(a) Ifadial forzesare Present(6) If axial compressior of 2 7o KN acts, and(() if axial tension A270 kN actsCompute Ve by both the muresu each Case,complea and Simplitied expressions af Ac I- cade. Neyleetthe self-weighl of the beum. At the seetion corsideved, tensikreinforemcut consist of three No. 31) with tetul angas2457mm?

Solution Given Data b=300 mm d=600 mm h=700 m

EZ-11 Abenan with dimeny, on} b=}. h=70o mm , with 28Mpu, Curries a fuctor load 440KN ut mizspan. fizd the mux. s hear strength of the coulrete (Vc) at the first critical section for shear at a distance (d) from the suppert feaed sidgle concentrated (a) If no aial forces (6) If axial compressior of 2 7o KN acts, and (() if axinl tension are Present acts A 270 KN compute Ve by both the mure ach Case

EZ-11 Abenan with dimeny, on} b=}. h=70o mm , with 28Mpu, Curries a fuctor load 440KN ut mizspan. fizd the mux. s hear strength of the coulrete (Vc) at the first critical section for shear at a distance (d) from the suppert feaed sidgle concentrated (a) If no aial forces (6) If axial compressior of 2 7o KN acts, and (() if axinl tension are Present acts A 270 KN compute Ve by both the mure ach Case

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid a pin at A and beam is Supprted by wires BD anod CE. IP the load P on the bean Cause the Point I to be displacedmm dovn warel. delermine to normal strain developd in wires CEard BD
two the stability of the Determine Structures. Supported by beams (3) A. This structure is facu feercor and has two beams the wall- Structure B. This 0 into mounted fatur SCAN ME Strains All FACTOR AL Facfo2: Past Factor A2: Vibie for A4 thich-Repa Factor AS: Restrictiv Featur B6: Concentra Ector (2! Monotomy Got 63 6ye Steau rector C1: Temp / He for CZ Ventilato rector CB: tumes
Structure w:- Analyze by the Con Sistend defor madion_method defor mation method EXH- the bean shown and then D raw S-F D and B-MD EI Canstamnt- sol. .A. 3+0 i Stad Indeteminade 3m to the 1st degree- one redundant) (M)E (2) |(* +here S priman det- Aio choose RB () redundant. as. 84 36 Str. nd3)=Rc(10) ieRc=367 Fjeo1 RA =84 KN1 mi * SMA= 0,4 Ix6=RCAlo RA=0.4 Sec. orig. timits. AD 0--3 84X AB 36 84x-12olk-) oi4 ¥3+X) 0 384(x-3)-120(x) 0-47 CB 36X
IjẩẩREẩjP3.4 Nylon rod (1): d Steel tube (2) FIGURE P3.7
Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
1) Find the allowable safe loadpf the stressec in the ban are fhe following BC - so ksi ABE GO feri CD = 70 ksi 0.4 in2 0.5 n2 0.3 n? op - P4 A 13
The papped cantilerer beam Andye Draw SFD Bno and Eleshc casre. Consiskent defomution methed. EI b constant bm
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
the ends tu three Of the Farcep Coupe f the rectonguler plate.are ycdal Couples e Determme So thot moment is 400 the the magnitude resultart Mm anticlackss 2m G-750 N -Q=-250M Calcalah the perpendralor drsknce be tween f ad -f. ard -f. the Coupe Ferces Calaulak Cauple the magntude Cf the Coupe momey Q 1.2. Of H 13 The directrcn OF the couple munmt a Oupir rs. Calcaek the Magnmuk e p
2- A steel pod is stretek between two rigid walls ard carries a tensile Coad 4GO0ON at c f the allowatle Stress is not to excred 130 MPa at -4C, what is the minimum the nd? diameter f ard E= J00 GPa. Figure: ST L
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A 90 kN L3 6m A= 0.04 m A = 0.06m² E=200 6AE=80 GPa L-4m