If our alloy has a composition of 10% Mi and has a temperature of 1100C, determine:a) What phase(s) are present?b) What are the compositions of these phasesc) What are the proportions of these phases in the alloy Use the following Phase Diagram for a Ge-Si alloy for the following questions:Ge - Si Alloy Phase Diagram15001400Liquid13001200Liquid1100100090020406080100Composition (wt% Si)Temperature (°C)

Answered: Image /qna-images/answer/a92c9f58-f4aa-4dfe-bc06-ebec8966e7ee.jpg

f our alloy has a composition of 10% Mi and has a temperature of 1100C, determine: ) What phase(s) are present? ) What are the compositions of these phases ) What are the proportions of these phases in the alloy

f our alloy has a composition of 10% Mi and has a temperature of 1100C, determine: ) What phase(s) are present? ) What are the compositions of these phases ) What are the proportions of these phases in the alloy

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Consider the magnesium oxide-aluminum oxide phase diagram; ss indicates a solid solution. The radii…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: omenclature 2 composition, 3 crystal structure 4 Phase Diagrams,

A: Spheroidal graphite iron, also referred to as ductile cast iron, nodular cast iron, SG iron, and…

Q: 700 L 600 500- (A1)+ (A1)+ O 400 (A1) emperature,

A: steps :- (1) solutioning (2) quenching (3) aging Maximum hardness will be obtained at an optimum…

Q: B) What is the difference between the Eutectic alloy and other alloy in the phase diagrams ? explain…

A: Eutectic alloy example: 4.3 % carbon cast iron 60% Sn- Pb-Sn alloy : solder

Q: 1. Calculate the composition of a lin (Sn)/ lead (Pb) alloy Lhat has the lowest melting point. Plot…

A: FIBER REINFORCEMENT 1.The properties of fiber reinforcement composites depend upon the following…

Q: Reproduce the binary phase diagram depicted in Fig. 3.20. For the composition shown at X, mark on…

A: Binary Phase diagrams: These are temperature vs composition diagrams in which two phases are…

Q: a)Draw the microstructure at each of the points A, B, C, D in the phase diagram given on the left.…

A: a) Iron carbon phase diagram from figure From the figure, it shows that at point A only the liquid…

Q: Sketch a phase diagram for two soluble components. Show the melting tem-perature of each element.…

A: The simplest type of phase diagram for any system can be of two components that are soluble in both…

Q: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F) (d) What is…

A: Solution: Given: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C…

Q: a) Find the percentages of the phases of alloy "1" in the figure at T1, T2 and T3 temperatures. b)…

A: The description of the diagram is shown below

Q: What is the maximum amount of Pb (in %) with which Sn may be alloyed to render a single β phase at…

Q: A 95cu-5AG copper-silver alloy is cooled slowly from 1100°C to 20°C. What phases at what…

Q: 5 wt% Fe-5.5 wt% C at a and types of The Phases t Of Phases Present in Gr Microstructure Of Phases

Q: ead-tin (Pb-Sn) is an eutectic type of phase diagram. At 183 °C, liquid (61.9 wt.% Sn), solid tin…

Q: Your friend in the lab has been working with a 90% Dc, 10% Vr alloy and developed the…

A: T-T-T (Time Temperature Transformation) diagram: The basis of heat treatment is the…

Q: Choose fhe correct anguer ? 7) The term allotropy is normally reserved for this behavior in pure…

A: 7. 1) elements Allotropy is the existence of two or more different physical forms of a chemical…

Q: Consider an alloy at composition C 1, just above the eutectic temperatdre. What are the phases…

A: Gigen :- Consider an alloy at composition C1 just above the eutectic temperature. What are the…

Q: 12) If you have an alloy with a composition of 50 wt% Ag at a temperature of 778.9° C, identify: a)…

A: Given for a Cu-Ag phase wt% of Ag is 50% Temperature = 778.9 degree C Eutectoid Temperature = 779…

Q: Figure 1.1: Cu - Ag Phase Diagram i. What Phases are present in the Alloy at 800° C? i. What are the…

Q: An 80 wt% Cu - 20 wt% Ni alloy is slowly cooled from 1250 °C to 1100 °C. T(°C) 1600 L (liquid) 1500…

A: Given Composition: 80 wt% Cu and 20 wt %Ni Initial temperature = 1250 C Final temperature = 1100 C…

Q: Consider the hypothetical eutectic phase diagram for metals A and B, which is similar to that for…

A: Write the formula for the mass fraction of the primary β component of the given alloy.…

Q: A binary alloy having 28 wt% Cu and balance Ag solidifies at 779°C. The solid consists of two phases…

A: Given: The alloy composition = 28%Ag

Q: For an alloy containing 20% Al- 80% Si (see figure 1 ), do the following: a) Determine the freezing…

Q: If our alloy has a composition of 10% i and has a temperature of 1100C, determim Si. a) What…

Q: For an Fe-0.35% C alloy, determine (a) the temperature at which austenite first begins to transform…

A: s more than three sub-parts are there in the question, first three sub-parts are answered.

Q: (a) Figure 5 shows a phase diagram for the Nb-80 wt% W alloy which is solidified under under the…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: Draw the iron-Fe3C phase diagram. Consider 0.4 and 1.1 wt% C steel alloy. It is cooled slowly from a…

A: As per our guidelines, only the first three subparts will be answered, Kindly ask other parts in…

Q: For the copper-nickel phase diagram of composition 60% Ni and 40% Cu. Draw the hanges in…

A: Draw a vertical line at 60 wt% Ni To draw changes in microstructure along this line during the…

Q: 11. What do you understand by the terms (i) static and (ii) dynamic methods for determination of…

A: In static method the alloy is held at a fixed temperature in the two phase field of solid and…

Q: a.) What type of binary phase diagram is Pb-Sn an example of?

A: Pb-Sn binary phase diagram is an example of "Eutectic system". A eutectic system has two components,…

Q: Q4) Explain the alloy formation process and the different between Binary and Triple or (Ternary)…

A: Alloy : Definition of Alloy A alloy is mainly combination or mixture of metals or metal with another…

Q: Determine the composition of each phase at 1300C, 1250C, and 1200C temperatures. Indicate wt%Ni of…

Q: Draw Fe-C binary phase diagram and compute percentage of the phases in eutectoid steel.

Q: Compare the Cu-Ni binary phase diagram with the Al2O3-Cr2O3 binary phase diagram. Why are they so…

A: Binary diagrams are the diagram which consists of two components. In which both can be metals (Cu…

Q: Use the Lead-Tin (Pb-Sn) phase diagram below to answer the following questions: Place the following…

A: Given:

Q: 2) There is an alum inum-copper alloy. The phase diagram is given below. What heat treatment do you…

A: Solution:

Q: For a 99.65 wt% Fe-0.35 wt% C alloy at a temperature just up the eutectoid teamperature, determine…

A: Given At 99.65% Fc -0.35 wt%

Q: Specify all temperature-compositicn points at which eutectics, eutectoids and peritectics. At 700…

A: Redraw the given phase diagram.

Q: A steel alloy is known to contain 93.8 wt% Fe, 6.0 wt% Ni, and 0.2 wt% C. Assume that there are no…

A: The change in the alloy steel with the eutectoid temperature, position of phase boundary, and…

Q: Describe experimental procedure to obtain a binary isomorphic phase diagram for metals A and B by…

Q: What is the crystal phases just above eutectoid temperature for a carbon steel with carbon…

Q: In Figure 1 (phase diagram), an alloy composition of 95 wt% Mg and 5 wt% Al is cooled from 700 C to…

A: given data: alloy composition =95wt%Mg and 5wt%Alcooled from 700to 4750cε composition??

Q: A 50 wt% Ni–50 wt% Cu alloy is slowly cooled from 1400°C (2550°F) to 1200°C (2190°F).…

Q: Draw the iron-Fe3C phase diagram. Consider 0.4 and 1.1 wt% C steel alloy. It is cooled slowly from a…

A: Carbon in iron is an interstitial impurity and forms alloys with iron, Steel is an alloy of iron and…

Q: Cu-Ni phase diagram is given below. 1500 1400 a + L -1270 1300 40 37

A: Phase diagram is an important tool to understand the compositional concentration of two or more…

Q: describe the extration of elemental composition; s from solid sample. Explain what major concern of…

A: given; describe the extraction of elemental composition; s from solid sample. Explain what major…

Q: Refer to Figure 1 showing the phase diagram for the Fe-Fe3C system. Consider 1.0 kg of austenite…

A: From the given information:

Q: 30. Select the letter of each image (A, B, C, etc.) that best reflects the microstructure at 700°C…

A: here, as instructed that as copper constitutes increases the dark part ( dark region or dark lines)…

Q: 6- What is the critical cooling rate for hardening? Explain. Explain the effects of alloying…

Question

If our alloy has a composition of 10% Mi and has a temperature of 1100C, determine:
a) What phase(s) are present?
b) What are the compositions of these phases
c) What are the proportions of these phases in the alloy

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Types of Phase Diagrams and Its Applications in Metallurgy

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Use the copper silver phase diagram below. 100g of a 40 wt% Cu 60 wt% Ag alloy is made and cooled from liquid form. a. At what temperature does the solid phase start to appear? b. What phases exist at 780°C? c. What are the compositions (Cu and Ag%) of the phases in question b? d. What are the weights (in g) of Cu in the solid phase and liquid phase in question b?
Answer the following questions using the phase diagram of iron and iron carbide below:For a 99.70 wt% Fe–0.30 wt% C alloy at a temperature of 600oC, determine the following:a. The fractions of total ferrite and cementite phases b. The fractions of the pro eutectoid ferrite and pearlite
Describe experimental procedure to obtain a binary isomorphic phase diagram for metals A and B by stating the equipment and materials you need? Show typical micrographs at 3 different phase regions for the alloy 50% A and 50% B on the phase diagram you obtained
For an Fe-0.35% C alloy, determine the composition and amount of each phase present at 726 ° C; and the composition and amount of each microconstituent present at 726 °C.
1-The microstructural design of Iron-Carbon(Fe-C) alloys has led to the development of vast range of steels for structural material applications. The phase diagram provide means for producing specific microstructures. Using the phase diagram below to answer the following questions A – If the liquid mixture of Fe-3%Wt C is slowly cooled from 1600 C to 1200C indicate the phase(S) that are present at 1200 C . Also calculate the composition of the of phases.(10) B-Describe the sequence of all phase transformation that accour from Fe-1.5%wt C is slowly cooled from 1600 C to 400 C. Use the diagram below to to describe the microstructures for each phase transformation (10)
Cite the phases that are present and the phase compositions for the following alloys: 85 wt% Ag–15 wt% Cu at 800°C
A hypo-eutectoid steel with composition of 0.5% carbon is heated to 1000°. Using the a iron-carbon phase diagram (also found in the course book, or here https://commons.wikimedia.org/wiki/File:Iron_carbon_phase_diagram.svg (Links to an external site.) (Links to an external site.)) answer the following questions. (a) What phase or phases will be present at 950°C? (b) If temperature is lowered from 950°C, at which temperature (estimate) α phase (Ferrite) will appear? (c) Use the lever rule to estimate how much (wt%) ferrite and how much austenite will exist just above 727 °C? (d) What happens to the austenite if the temperature is lowered below 727 °C? (e) Schematically sketch and label the resulting microstructure.
The engineering yield strength of an alloy is 80 ksi.
Copper-Nickel alloy is widely applied in industry. (a) List at least three applications where Cu-Ni alloy is used; (b) How many components and phases are shown in the below phase diagram? (c) For a mixture of 40 wt% Cu and 60 wt% Ni at 1320 oC, what phases are present? Identify theamount of these phases by applying “lever rule”.
In the iron carbon phases diagram, Greek letters and names of structures are used L liquid metal FE 3C iron carbide Delta Delta iron gamma gamma iron called austenite alpha alpha iron called ferrite true or false?
Specification of Composition 3). Calculate the composition, in weight percent, of an alloy that contains 218.0 kg titanium, 14.6 kg of aluminum, and 9.7 kg of vanadium. 4.) What is the composition, in atom percent, of an alloy that contains 99.7 lbm copper, 102 lbm zinc, and 2.1 lbm lead? Atomic weights of Cu, Zn and Pb are 63.55 g/mol, 65.41 g/mol, and 207.2 g/mol, respectively. [Procedure] (i) Convert lbm into gram (1 lbm =453.6 g); (ii) Calculate moles of Cu, Zn, and Pb; (iii) calculate atom percent
BINARY PHASE DIAGRAMS Please only answer parts d and e as the rest have been solved. Show full detailed explanation to answers with diagrams if necessary a)(i) What is the melting point of pure Mg?(ii) What is the maximum solubility of Mg in Pb and at what temperaturedoes this occur? (b) A 50 wt.% Pb-50wt% Mg alloy is slowly cooled from 700 °C to 400 °C.(i) At what temperature does the first solid phase form?(ii) What is the composition of this solid phase?(iii) At what temperature does all the liquid solidify?(iv) What is the composition of the last remaining liquid phase?(v) What is the freezing range? (c) What is the mass fraction of solid and liquid of a 60 wt.% Mg alloy at atemperature of 500 °C.(d) Draw and label the microstructure of an 80 wt.% Mg alloy at 600 °C.(e) A Mg-Pb alloy of mass 5.5 kg has a composition just slightly below thesolubility limit of 200 °C.(i) What mass of lead is in the alloy?(ii) If the alloy is heated to 350 °C how much more lead can be dissolvedin…